WPL-05G300、シリアル取り出し。

某社のPLC、WPL-05G300のシリアルの取り出しです。
AR7400とAR9341の両方シリアルが存在する形になります。
AR7400は、PLC箇所。こちらはピンがもともと存在するが、AC100Vを刺した状態で取り出しにくいので、ピンを付けかえれば良いでしょう。
AR9341は、WiFi箇所。メイン側と考えて良いだろうが、取り出しやすい場所がなかなか判断しにくい。
レジストを剥がしつつ2本取り出します。細いので半田付け慣れしていない場合は辞めた方が良いでしょう。(僕も下手なのであまり手を出したくなかった)

AR9341のシリアル引き出し結果です。
すみません、補強する前に写真撮り忘れました。
シールドはひっぺがして2本取り出します。GNDは適当に取ります。


AR9341のGPIO9、GPIO10がUARTに対応するので、対応する場所から追います。
GPIO10は隠れているので、GPIO9の隣位置の奥から出ている事になります。
ピン箇所は、データシートに記載されています。
AR9341のデータシートはすぐみつかります。



赤色で印した箇所が、UARTになります。
レジストされているので、少し剥がして線を伸ばします。
はんだ馴れしていれば楽勝でしょう。
僕は慣れていないので、後から補強しました。



次に予想外だったのが、ボーレートがubootとlinuxで異なる点。
しかも、ubootが何故か121212ときました。
たしかにこれでシリアルと思わずスルーする人も多そうです。
ubootは121212で、linuxは115200になります。
121212とは良い趣味してますね。開発者さん。

===========================================
BUFFALO U-BOOT Ver 011
============================================
Product name : WPL-05G300
CPU(srif) : 535
DRAM(srif) : 400
AHB : 200
Start init DRAM:  
DDR2 init : wasp_ddr_initial_config(251): (16bit,Tap value selected = 0xf [0x0 - 0x1f]
64 MB
Init DRAM : Success
Memory Test (address line)
Memory Test start(0x00000000) end(0x04000000) size(67108864)
Data line test start:0x00000000 pattern 0x00000001 0x00000003 0x00000007 0x0000000F 0x00000005 0x00000015 0x00000055 0xAAAAAAAA 
Address line test start:0x00000000 len:0x4000000 pattern 0xAAAAAAAA 0x55555555  
Fill test patnum:5 
fill Pattern 5555AAAA  Writing...             Reading...
fill Pattern AAAA5555  Writing...             Reading...
fill Pattern 0000FFFF  Writing...             Reading...
fill Pattern FFFF0000  Writing...             Reading...
fill Pattern AAAAAAAA  Writing...             Reading...
Top of RAM usable for U-Boot at: 84000000
Reserving 253k for U-Boot at: 83fc0000
Reserving 192k for malloc() at: 83f90000
Reserving 44 Bytes for Board Info at: 83f8ffd4
Reserving 36 Bytes for Global Data at: 83f8ffb0
Reserving 128k for boot params() at: 83f6ffb0
Stack Pointer at: 83f6ff98
Now running in RAM - U-Boot at: 83fc0000
id read 0x100000ff
flash size 8MB, sector count = 128
Flash:  8 MB
In:    serial
Out:   serial
Err:   serial
### buf_ver=[011]
@@@ U-Boot Ver.=[011]
### build_date(env)=[Jan  4 2012 - 15:19:27]
@@@ build_date(bin)=[Jan  4 2012 - 15:19:27]
ag934x_enet_initialize...
Fetching MAC Address from 0x83febab8
Fetching MAC Address from 0x83febab8
 wasp  reset mask:c03300 
eth0: 4c:e6:76:9a:6e:ff
Init WAN port 
eth0 up
eth1: 4c:e6:76:9a:6e:ff
Init LAN port 
eth1 up
eth0, eth1
## Booting image at 9f050000 ...
   Image Name:   Linux Rootfs Combined Image
   Created:      2012-08-01   3:38:01 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    5038016 Bytes =  4.8 MB
   Load Address: 80002000
   Entry Point:  801e4c30
   Verifying Checksum at 0x9f050040 ...insmod: /lib/modules/2.6.31--LSDK-9.2.0.106: No such file or directory
Using /lib/modules/kernel/drivers/char/mel_initsw.ko
mel_initsw_ar7400_wpl_05g300: module license 'unspecified' taints kernel.
Disabling lock debugging due to kernel taint
mel_initsw initialized. 

Please press Enter to activate this console. watchdogd.c(33) watchdogd_main :watchdog refresh 00000000
WD:Start Watchdog Daemon
Algorithmics/MIPS FPU Emulator v1.5
sample: not found
rc.c(344) VerifyParamsOfInit :x:create status sections
rc.c(816) SetUbootParam :====:pUbootProduct=WPL-05G300
rc.c(826) SetUbootParam :====:pProductHex=00000001(str:00000001)
wlctl-ath.c(6091) Wireless_Insmod :ERR:####### Wireless_Insmod #########
insmod: /lib/modules/2.6.31--LSDK-9.2.0.106: No such file or directory
Using /lib/modules/2.6.31/net/adf.ko
insmod: /lib/modules/2.6.31--LSDK-9.2.0.106: No such file or directory
Using /lib/modules/2.6.31/net/asf.ko
insmod: /lib/modules/2.6.31--LSDK-9.2.0.106: No such file or directory
Using /lib/modules/2.6.31/net/ath_hal.ko
ath_hal: 0.9.17.1 (AR5416, AR9380, REGOPS_FUNC, WRITE_EEPROM, 11D)
insmod: /lib/modules/2.6.31--LSDK-9.2.0.106: No such file or directory
Using /lib/modules/2.6.31/net/ath_rate_atheros.ko
ath_rate_atheros: Copyright (c) 2001-2005 Atheros Communications, Inc, All Rights Reserved
insmod: /lib/modules/2.6.31--LSDK-9.2.0.106: No such file or directory
Using /lib/modules/2.6.31/net/ath_dfs.ko
ath_dfs: Version 2.0.0
Copyright (c) 2005-2006 Atheros Communications, Inc. All Rights Reserved
insmod: /lib/modules/2.6.31--LSDK-9.2.0.106: No such file or directory
Using /lib/modules/2.6.31/net/ath_dev.ko
ath_dev: Copyright (c) 2001-2007 Atheros Communications, Inc, All Rights Reserved
insmod: /lib/modules/2.6.31--LSDK-9.2.0.106: No such file or directory
Using /lib/modules/2.6.31/net/ath_pktlog: Unknown symbol ath_get_softc
ath_pktlog.ko
------------[ cut here ]------------
WARNING: at lib/kobject.c:595 kobject_put+0x40/0x6c()
kobject: '' (c0229f98): is not initialized, yet kobject_put() is being called.
Modules linked in: ath_dev(P) ath_dfs(P) ath_rate_atheros(P) ath_hal(P) asf(P) adf mel_initsw_ar7400_wpl_05g300(P)
Call Trace:
[<801e64ec>] dump_stack+0x8/0x34
[<80023ebc>] warn_slowpath_common+0x70/0xb0
[<80023f3c>] warn_slowpath_fmt+0x24/0x30
[<800e6470>] kobject_put+0x40/0x6c
[<80045df8>] load_module+0x12f8/0x1478
[<8004636c>] sys_init_module+0x70/0x214
[<8000e244>] stack_done+0x20/0x3c

---[ end trace a816c556ee7d3536 ]---
insmod: cannot insert `/lib/modules/2.6.31/net/ath_pktlog.ko': Invalid parameters (2): Invalid argument
wlctl-ath.c(6006) AtherosWirelessBaseModules_Insmod :####:insmod ath_pktlog : FAILED (Perhaps, [ath_pktlog] has already been added.)
insmod: /lib/modules/2.6.31--LSDK-9.2.0.106: No such file or directory
Using /lib/modules/2.6.31/net/umac.ko
ath_ahb: 9.2.0_U6.616 (Atheros/multi-bss)
__ath_attach: Set global_scn[0]
ACBKMinfree = 48
ACBEMinfree = 32
ACVIMinfree = 16
ACVOMinfree = 0
CABMinfree = 48
UAPSDMinfree = 0
wl0: start wireless chip
Restoring Cal data from Flash
dfs_attach: use DFS enhancements
dfs_init_radar_filters: Unknown dfs domain 0
ath_get_caps[4898] rx chainmask mismatch actual 3 sc_chainmak 0
ath_get_caps[4873] tx chainmask mismatch actual 3 sc_chainmak 0
SC Callback Registration for wifi0
wifi0: Atheros 9340: mem=0xb8100000, irq=2
wlctl-ath.c(1153) wlconf_country_set :DEBUG:region=JP iCountryCode=4015
DFS min filter rssiThresh = 18
DFS max pulse dur = 151 ticks
wlan_vap_create : enter. devhandle=0x83b902c0, opmode=IEEE80211_M_HOSTAP, flags=0x1
/opt/snapshot/snapshot_WPL-05G300/1.85_4.06_2012-08-01-11-43-JST_WPL-05G300-JP-US-EU-AP/linux-2.6.31-ath-ap123/src/wlan-ap123/os/linux/../../umac/mlme/ieee80211_proto.c(132): wlan_scan_register_event_handler(8304E000,C034F4A8,8304E000) call
wlan_vap_create : exit. devhandle=0x83b902c0, opmode=IEEE80211_M_HOSTAP, flags=0x1.
VAP device ath0 created 
/opt/snapshot/snapshot_WPL-05G300/1.85_4.06_2012-08-01-11-43-JST_WPL-05G300-JP-US-EU-AP/linux-2.6.31-ath-ap123/src/wlan-ap123/os/linux/../../umac/../os/linux/src/osif_umac.c(3901): wlan_scan_register_event_handler(8304E000,C0383E94,83B15AC0) call
Invalid command : extoffset
Invalid command : cwmmode
wlan_vap_create : enter. devhandle=0x83b902c0, opmode=IEEE80211_M_HOSTAP, flags=0x1
/opt/snapshot/snapshot_WPL-05G300/1.85_4.06_2012-08-01-11-43-JST_WPL-05G300-JP-US-EU-AP/linux-2.6.31-ath-ap123/src/wlan-ap123/os/linux/../../umac/mlme/ieee80211_proto.c(132): wlan_scan_register_event_handler(8316A000,C034F4A8,8316A000) call
wlan_vap_create : exit. devhandle=0x83b902c0, opmode=IEEE80211_M_HOSTAP, flags=0x1.
VAP device ath1 created 
/opt/snapshot/snapshot_WPL-05G300/1.85_4.06_2012-08-01-11-43-JST_WPL-05G300-JP-US-EU-AP/linux-2.6.31-ath-ap123/src/wlan-ap123/os/linux/../../umac/../os/linux/src/osif_umac.c(3901): wlan_scan_register_event_handler(8316A000,C0383E94,83B152C0) call
Invalid command : extoffset
Invalid command : cwmmode
wlan_vap_create : enter. devhandle=0x83b902c0, opmode=IEEE80211_M_HOSTAP, flags=0x1
/opt/snapshot/snapshot_WPL-05G300/1.85_4.06_2012-08-01-11-43-JST_WPL-05G300-JP-US-EU-AP/linux-2.6.31-ath-ap123/src/wlan-ap123/os/linux/../../umac/mlme/ieee80211_proto.c(132): wlan_scan_register_event_handler(8316C000,C034F4A8,8316C000) call
wlan_vap_create : exit. devhandle=0x83b902c0, opmode=IEEE80211_M_HOSTAP, flags=0x1.
VAP device ath2 created 
/opt/snapshot/snapshot_WPL-05G300/1.85_4.06_2012-08-01-11-43-JST_WPL-05G300-JP-US-EU-AP/linux-2.6.31-ath-ap123/src/wlan-ap123/os/linux/../../umac/../os/linux/src/osif_umac.c(3901): wlan_scan_register_event_handler(8316C000,C0383E94,8315FAC0) call
Invalid command : extoffset
Invalid command : cwmmode
wlan_vap_create : enter. devhandle=0x83b902c0, opmode=IEEE80211_M_HOSTAP, flags=0x1
/opt/snapshot/snapshot_WPL-05G300/1.85_4.06_2012-08-01-11-43-JST_WPL-05G300-JP-US-EU-AP/linux-2.6.31-ath-ap123/src/wlan-ap123/os/linux/../../umac/mlme/ieee80211_proto.c(132): wlan_scan_register_event_handler(83170000,C034F4A8,83170000) call
wlan_vap_create : exit. devhandle=0x83b902c0, opmode=IEEE80211_M_HOSTAP, flags=0x1.
VAP device ath3 created 
/opt/snapshot/snapshot_WPL-05G300/1.85_4.06_2012-08-01-11-43-JST_WPL-05G300-JP-US-EU-AP/linux-2.6.31-ath-ap123/src/wlan-ap123/os/linux/../../umac/../os/linux/src/osif_umac.c(3901): wlan_scan_register_event_handler(83170000,C0383E94,8315F2C0) call
Invalid command : extoffset
Invalid command : cwmmode
insmod: /lib/modules/2.6.31--LSDK-9.2.0.106: No such file or directory
Using /lib/modules/2.6.31/net/athrs_gmac.ko
mac:0 Registering S27....
mac:1 Registering S27....
insmod: /lib/modules/2.6.31--LSDK-9.2.0.106: No such file or directory
Using /lib/modules/kernel/net/ipv4/netfilter/nf_conntrack_proto_gre.ko
insmod: /lib/modules/2.6.31--LSDK-9.2.0.106: No such file or directory
Using /lib/modules/kernel/net/ipv4/netfilter/nf_nat_proto_gre.ko
wanctl-lib.c(1308) CallIoctlOnEtherdeviceEx :ERR:!! Failed ioctl() !! ifr_name:[eth0] a_iCmd:[35093(-219)]:a_iCommand errorcode:126
Cannot assign requested address
wanctl-lib.c(1308) CallIoctlOnEtherdeviceEx :ERR:!! Failed ioctl() !! ifr_name:[eth0] a_iCmd:[35093(-219)]:a_iCommand errorcode:126
Cannot assign requested address
rc.c(816) SetUbootParam :====:pUbootProduct=WPL-05G300
rc.c(826) SetUbootParam :====:pProductHex=00000001(str:00000001)
wlctl-ath.c(6091) Wireless_Insmod :ERR:####### Wireless_Insmod #########
insmod: /lib/modules/2.6.31--LSDK-9.2.0.106: No such file or directory
Using /lib/modules/2.6.31/net/adf.ko
insmod: cannot insert `/lib/modules/2.6.31/net/adf.ko': Invalid parameters (17): Invalid argument
wlctl-ath.c(6006) AtherosWirelessBaseModules_Insmod :####:insmod adf : FAILED (Perhaps, [adf] has already been added.)
insmod: /lib/modules/2.6.31--LSDK-9.2.0.106: DFS min filter rssiThresh = 22
No such file or DFS max pulse dur = 151 ticks
directory
Using /lib/modules/2.6.31/net/umac.ko
insmod: cannot insert `/lib/modules/2.6.31/net/umac.ko': Invalid parameters (17): Invalid argument
wlctl-ath.c(6122) Wireless_Insmod :####:insmod umac : FAILED
wlctl-ath.c(1153) wlconf_country_set :DEBUG:region=JP iCountryCode=4015
wlanconfig: ioctl: Invalid argument
Invalid command : extoffset
Invalid command : cwmmode
wlanconfig: ioctl: Invalid argument
Invalid command : extoffset
Invalid command : cwmmode
wlanconfig: ioctl: Invalid argument
Invalid command : extoffset
Invalid command : cwmmode
wlanconfig: ioctl: Invalid argument
Invalid command : extoffset
Invalid command : cwmmode
insmod: /lib/modules/2.6.31--LSDK-9.2.0.106: No such file or directory
Using /lib/modules/2.6.31/net/athrs_gmac.ko
insmod: cannot insert `/lib/modules/2.6.31/net/athrs_gmac.ko': Invalid parameters (17): Invalid argument
insmod: /lib/modules/2.6.31--LSDK-9.2.0.106: No such file or directory
Using /lib/modules/kernel/net/ipv4/netfilter/nf_conntrack_proto_gre.ko
insmod: cannot insert `/lib/modules/kernel/net/ipv4/netfilter/nf_conntrack_proto_gre.ko': Invalid parameters (17): Invalid argument
insmod: /lib/modules/2.6.31--LSDK-9.2.0.106: No such file or directory
Using /lib/modules/kernel/net/ipv4/netfilter/nf_nat_proto_gre.ko
insmod: cannot insert `/lib/modules/kernel/net/ipv4/netfilter/nf_nat_proto_gre.ko': Invalid parameters (17): Invalid argument
MidLayerModDep.c(807) startModules :INFO:Starting module init
mknod: /dev/ppp: File exists
insmod: /lib/modules/2.6.31--LSDK-9.2.0.106: No such file or directory
insmod: slhc.ko: no module by that name found
insmod: /lib/modules/2.6.31--LSDK-9.2.0.106: No such file or directory
insmod: ppp_generic.ko: no module by that name found
insmod: /lib/modules/2.6.31--LSDK-9.2.0.106: No such file or directory
insmod: ppp_mppe.ko: no module by that name found
insmod: /lib/modules/2.6.31--LSDK-9.2.0.106: No such file or directory
insmod: ppp_async.ko: no module by that name found
insmod: /lib/modules/2.6.31--LSDK-9.2.0.106: No such file or directory
insmod: ppp_synctty.ko: no module by that name found
insmod: /lib/modules/2.6.31--LSDK-9.2.0.106: No such file or directory
insmod: pppox.ko: no module by that name found
insmod: /lib/modules/2.6.31--LSDK-9.2.0.106: No such file or directory
insmod: pppoe.ko: no module by that name found
insmod: /lib/modules/2.6.31--LSDK-9.2.0.106: No such file or directory
insmod: zlib_deflate.ko: no module by that name found
insmod: /lib/modules/2.6.31--LSDK-9.2.0.106: No such file or directory
insmod: ppp_deflate.ko: no module by that name found
MidLayerModDep.c(819) startModules :INFO:Started  module init 153[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_tz
MidLayerModDep.c(819) startModules :INFO:Started  module rc_tz 1[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_syslogd
MidLayerModDep.c(819) startModules :INFO:Started  module rc_syslogd 34[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_klogd
MidLayerModDep.c(819) startModules :INFO:Started  module rc_klogd 17[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_mode_check
insmod: /lib/modules/2.6.31--LSDK-9.2.0.106: No such file or directory
Using /lib/modules/2.6.31/net/athrs_gmac.ko
insmod: cannot insert `/lib/modules/2.6.31/net/athrs_gmac.ko': Invalid parameters (17): Invalid argument
MidLayerModDep.c(819) startModules :INFO:Started  module rc_mode_check 1027[msec]
MidLayerModDep.c(807) startModules :INFO:Starathrs27_force_MDI_WPL: phyAddr = (0)
ting module rc_lPHY_FUNC_CONTROL = (ffff) -> (860)
oif
MidLayerModet0: unit: phy 0 is up...
Dep.c(819) startModules :INFO:Started  module rc_loif 5[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_routeFUNCTION: athrs27_phy_speed, ethUnit = (0), phyUnit = (0)
r_behavior
MidLUnkown speed read!
ayerModDep.c(819FUNCTION: athrs27_phy_speed, ethUnit = (0), phyUnit = (0)
) startModules :Unkown speed read!
INFO:Started  module rc_router_behavior 0[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module init
MidLayerModDep.c(819) startModules :INFO:StartedFUNCTION: athrs27_phy_speed, ethUnit = (0), phyUnit = (0)
  module init 3[Unkown speed read!
msec]
MidLayerModDep.c(807) staFUNCTION: athrs27_phy_speed, ethUnit = (0), phyUnit = (0)
rtModules :INFO:Unkown speed read!
Starting module athrs27_force_MDI_WPL: phyAddr = (1)
rc_wiredlan
PHY_FUNC_CONTROL = (0) -> (860)
athrs27_force_MDI_WPL: phyAddr = (2)
PHY_FUNC_CONTROL = (ffff) -> (860)
athrs27_force_MDI_WPL: phyAddr = (3)
PHY_FUNC_CONTROL = (ffff) -> (860)
athrs27_force_MDI_WPL: phyAddr = (4)
PHY_FUNC_CONTROL = (ffff) -> (860)
athrs27_force_MDI_WPL: phyAddr = (1)
PHY_FUNC_CONTROL = (4001) -> (860)
athrs27_force_MDI_WPL: phyAddr = (2)
PHY_FUNC_CONTROL = (ffff) -> (860)
athrs27_force_MDI_WPL: phyAddr = (3)
PHY_FUNC_CONTROL = (ffff) -> (860)
athrs27_force_MDI_WPL: phyAddr = (4)
PHY_FUNC_CONTROL = (ffff) -> (860)
et1: unit: phy 4 is up...
FUNCTION: athrs27_phy_speed, ethUnit = (1), phyUnit = (1)
Unkown speed read!
FUNCTION: athrs27_phy_speed, ethUnit = (1), phyUnit = (2)
Unkown speed read!
FUNCTION: athrs27_phy_speed, ethUnit = (1), phyUnit = (3)
Unkown speed read!
FUNCTION: athrs27_phy_speed, ethUnit = (1), phyUnit = (4)
Unkown speed read!
athrs27_force_MDI_WPL: phyAddr = (1)
PHY_FUNC_CONTROL = (ffff) -> (860)
athrs27_force_MDI_WPL: phyAddr = (2)
PHY_FUNC_CONTROL = (1) -> (860)
athrs27_force_MDI_WPL: phyAddr = (3)
PHY_FUNC_CONTROL = (ffff) -> (860)
et1: unit: phy 3 is up...
FUNCTION: athrs27_phy_speed, ethUnit = (1), phyUnit = (1)
Unkown speed read!
FUNCTION: athrs27_phy_speed, ethUnit = (1), phyUnit = (2)
Unkown speed read!
FUNCTION: athrs27_phy_speed, ethUnit = (1), phyUnit = (3)
Unkown speed read!
FUNCTION: athrs27_phy_speed, ethUnit = (1), phyUnit = (4)
Unkown speed read!
athrs27_force_MDI_WPL: phyAddr = (1)
PHY_FUNC_CONTROL = (ffff) -> (860)
athrs27_force_MDI_WPL: phyAddr = (2)
PHY_FUNC_CONTROL = (ffff) -> (860)
FUNCTION: athrs27_phy_speed, ethUnit = (1), phyUnit = (1)
Unkown speed read!
FUNCTION: athrs27_phy_speed, ethUnit = (1), phyUnit = (2)
Unkown speed read!
FUNCTION: athrs27_phy_speed, ethUnit = (1), phyUnit = (3)
Unkown speed read!
FUNCTION: athrs27_phy_speed, ethUnit = (1), phyUnit = (4)
Unkown speed read!
athrs27_force_MDI_WPL: phyAddr = (1)
PHY_FUNC_CONTROL = (ffff) -> (860)
athrs27_force_MDI_WPL: phyAddr = (2)
PHY_FUNC_CONTROL = (ffff) -> (860)
FUNCTION: athrs27_phy_speed, ethUnit = (1), phyUnit = (1)
Unkown speed read!
FUNCTION: athrs27_phy_speed, ethUnit = (1), phyUnit = (2)
Unkown speed read!
FUNCTION: athrs27_phy_speed, ethUnit = (1), phyUnit = (3)
Unkown speed read!
FUNCTION: athrs27_phy_speed, ethUnit = (1), phyUnit = (4)
Unkown speed read!
ATHRS27: resetting s27
ATHRS27: s27 reset done
athrs27_force_MDI_WPL: phyAddr = (1)
PHY_FUNC_CONTROL = (802) -> (860)
athrs27_force_MDI_WPL: phyAddr = (2)
PHY_FUNC_CONTROL = (0) -> (860)
athrs27_force_MDI_WPL: phyAddr = (3)
PHY_FUNC_CONTROL = (2) -> (860)
athrs27_force_MDI_WPL: phyAddr = (4)
PHY_FUNC_CONTROL = (2) -> (860)
athrs27_force_MDI_WPL: phyAddr = (1)
PHY_FUNC_CONTROL = (862) -> (860)
athrs27_force_MDI_WPL: phyAddr = (2)
PHY_FUNC_CONTROL = (862) -> (860)
athrs27_force_MDI_WPL: phyAddr = (3)
PHY_FUNC_CONTROL = (862) -> (860)
athrs27_force_MDI_WPL: phyAddr = (4)
PHY_FUNC_CONTROL = (862) -> (860)
MidLayerModDep.c(819) startModules :INFO:Started  module rc_wiredlan 3851[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module id
MidLayerModDep.c(819) startModules :INFO:Started  module id 2[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_lanif
wlctl-ath.c(6091) Wireless_Insmod :ERR:####### Wireless_Insmod #########
insmod: /lib/modules/2.6.31--LSDK-9.2.0.106: No such file or directory
Using /lib/modules/2.6.31/net/adf.ko
indfs_init_radar_filters: Unknown dfs domain 0
smod: cannot insert `/lib/modules/2.6.31/net/adf.ko': Invalid parameters (17): Invalid argument
wlctl-ath.c(6006) AtherosWirelessBaseModules_Insmod :####:insmod adf : FAILED (Perhaps, [adf] has already been added.)
insmod: /lib/modules/2.6.31--LSDK-9.2.0.106: No such file or directory
Using /lib/modules/2.6.31/net/umac.ko
insmod: cannot insert `/lib/modules/2.6.31/net/umac.ko': Invalid parameters (17): Invalid argument
wlctl-ath.c(6122) Wireless_Insmod :####:insmod umac : FAILED
wlctl-ath.c(1153) wlconf_country_set :DEBUG:region=JP iCountryCode=4015
wlanconfig: ioctl: Invalid argument
Invalid command : extoffset
Invalid command : cwmmode
wlanconfig: ioctl: Invalid argument
Invalid command : extoffset
Invalid command : cwmmode
wlanconfig: ioctl: Invalid argument
Invalid command : extoffset
Invalid command : cwmmode
wlanconfig: ioctl: Invalid argument
Invalid command : extoffset
Invalid command : cwmmode
insmod: /lib/modules/2.6.31--LSDK-9.2.0.106: No such file or directory
Using /lib/modules/kernel/drivers/buffalo/mcsnoop.ko
mcsnoop: flush all snoop entry
rc_lanif.c(430) StartOfrc_lanif :x:PPPoE Path throw?


mcsnoop_br_ioctl_device:240: mcast_maxage 75000 / 250
wanctl-lib.c(1308) CallIoctlOnEtherdeviceEx :ERR:!! Failed ioctl() !! ifr_name:[eth0] a_iCmd:[35093(-219)]:a_iCoathrs27_force_MDI_WPL: phyAddr = (1)
PHY_FUNC_CONTROL = (862) -> (860)
athrs27_force_MDI_WPL: phyAddr = (2)
PHY_FUNC_CONTROL = (862) -> (860)
et1: unit: phy 2 is up...
athrs27_force_MDI_WPL: phyAddr = (3)
PHY_FUNC_CONTROL = (862) -> (860)
athrs27_force_MDI_WPL: phyAddr = (4)
PHY_FUNC_CONTROL = (862) -> (860)
FUNCTION: athrs27_phy_speed, ethUnit = (1), phyUnit = (2)
ATHR_PHY_SPEED_10T!
mmand errorcode:126
Cannot assiFUNCTION: athrs27_phy_speed, ethUnit = (1), phyUnit = (2)
gn requested addATHR_PHY_SPEED_10T!
ress
MidLayerModDep.c(819) startModules :INFO:Started  module rc_lanif 320[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_udhcpd
udhcpd (v0.9.9-pre) started
max_leases value (256) not sane, setting to 64 instead
MidLayerModDep.c(819) startModules :INFO:Started  module rc_udhcpd 76[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_httpd
MidLayerModDep.c(819) startModules :INFO:Started  module rc_httpd 19[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_wireless_pre
wlctl-ath.c(6091) Wireless_Insmod :ERR:####### Wireless_Insmod #########
insmod: /lib/modules/2.6.31--LSDK-9.2.0.106: No such file or directory
Using /lib/modules/2.6.31/net/adf.ko
insmod: cannot insert `/lib/modules/2.dfs_init_radar_filters: Unknown dfs domain 0
6.31/net/adf.ko': Invalid parameters (17): Invalid argument
wlctl-ath.c(6006) AtherosWirelessBaseModules_Insmod :####:insmod adf : FAILED (Perhaps, [adf] has already been added.)
insmod: /lib/modules/2.6.31--LSDK-9.2.0.106: No such file or directory
Using /lib/modules/2.6.31/net/umac.ko
insmod: cannot insert `/lib/modules/2.6.31/net/umac.ko': Invalid parameters (17): Invalid argument
wlctl-ath.c(6122) Wireless_Insmod :####:insmod umac : FAILED
wlctl-ath.c(1153) wlconf_country_set :DEBUG:region=JP iCountryCode=4015
wlanconfig: ioctl: Invalid argument
Invalid command : extoffset
Invalid command : cwmmode
wlanconfig: ioctl: Invalid argument
Invalid command : extoffset
Invalid command : cwmmode
wlanconfig: ioctl: Invalid argument
Invalid command : extoffset
Invalid command : cwmmode
wlanconfig: ioctl: Invalid argument
Invalid command : extoffset
Invalid command : cwmmode
Waiting for Wireless Events from interfaces...
MidLayerModDep.c(819) startModules :INFO:Started  module rc_wireless_pre 213[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_wireless11bg
Invalid command : bgscan
 
 DES SSID SET=BUFFALO-9A6EFF 
Warning: Driver for device ath0 has been compiled with version 2 ieee80211_ioctl_siwmode: imr.ifm_active=131712, new mode=3, valid=1 
2
of Wireless Extension, while this program supports up to version 20.
Some things may be broken...

15:00:06.584837   ath0     Set Channel:0
15:00:06.597022   ath0     Set Mode:Master
Interface doesn't accept private ioctl...
burst (8BE0): Operation not supported
Interface doesn't accept private ioctl...
acm (8BE3): Invalid argument
Interface doesn't accept private ioctl...
acm (8BE3): Invalid argument
Interface doesn't accept private ioctl...
acm (8BE3): Invalid argument
Interface doesn't accept private ioctl...
acm (8BE3): Invalid argument
set Buffalo Capability = 00000009
MidLayerModDep.c(819) startModules :INFO:Started  module rc_wireless11bg 1123[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_wireless11bg_mac_limit
MidLayerModDep.c(819) startModules :INFO:Started  module rc_wireless11bg_mac_limit 32[msec]
MidLayerModDep.c(807) startModules :INFO:Starting mieee80211_state_event: vap0 staet:INIT node:1  vap:8304e000
odule rc_wireles/opt/snapshot/snapshot_WPL-05G300/1.85_4.06_2012-08-01-11-43-JST_WPL-05G300-JP-US-EU-AP/linux-2.6.31-ath-ap123/src/wlan-ap123/os/linux/../../umac/acs/ieee80211_acs.c(1043): wlan_scan_register_event_handler(8304E000,C0367438,8396E000) call
s_post
MidLayerModDep.c(819) startModules :INFO:Started  module rc_wireless_post 91[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_nas
killall: hostapd: no process killed
MidLayerModDep.c(819) startModules :INFO:Started  module rc_nas 154[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_aoss_mssid
MidLayerModDep.c(819) startModules :INFO:Started  module rc_aoss_mssid 30[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_ap_serv
Configuration fi ieee80211_ioctl_siwmode: imr.ifm_active=393856, new mode=3, valid=1 
le: /tmp/hostapd Scan in progress.. Cancelling it 
.conf_ath0
->setpid 0x47b080
pid: /var/run/hostapd.ath0.pid
15:00:07.978596   ath0     Set Mode:Master
/opt/snapshot/snapshot_WPL-05G300/1.85_4.06_2012-08-01-11-43-JST_WPL-05G300-JP-US-EU-AP/linux-2.6.31-ath-ap123/src/wlan-ap123/os/linux/../../umac/acs/ieee80211_acs.c(852): wlan_scan_unregister_event_handler(8304E000,C0367438,8396E000) call
ieee80211_state_event: vap0 staet:INIT node:1  vap:8304e000
ath_beacon_config_ap_mode: called reason:1 if_id:0
ath_beacon_config_ap_mode: called reason:0 if_id:0
ieee80211_state_event: vap0 staet:STOPPING node:1  vap:8304e000
Using interface ath0 with hwaddr 4c:e6:76:9a:6e:ff and ssid 'BUFFALO-9A6EFF'
MidLayerModDep.c(819) startModules :INFO:Started  module rc_ap_serv 341[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_wanif
wanctl-lib.c(1308) CallIoctlOnEtherdeviceEx :ERR:!! Failed ioctl() !! ifr_name:[eth0] a_iCmd:[35093(-219)]:SIOCGIFADDR errorcode:126
Cannot assign requested address
athrs27_force_MDI_WPL: phyAddr = (0)
PHY_FUNC_CONTROL = (862) -> (860)
 
 DES SSID SET=BUFFALO-9A6EFF 
ieee80211_state_event: vap0 staet:INIT node:1  vap:8304e000
ieee80211_state_event: vap0 staet:INIT node:1  vap:8304e000
ath_beacon_config_ap_mode: called reason:1 if_id:0
Flushing old station entries
Deauthenticate all stations
l2_packet_receive - recvfrom: Network is down
l2_packet_receive - recvfrom: Network is down
MidLayerModDep.c(819) startModules :INFO:Started  module rc_wanif 3520[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_wanctl_pre
wanctl-lib.c(130##### ETHTOOL_SSET 2 : WAN, PHY(0), AUTONEG_ENABLE #####
8) CallIoctlOnEtherdeviceEx :ERR:!! Failed ioctl() !! ifr_name:[eth0] a_iCmd:[35323(11)]:a_iCmd errorcode:1
Operation not permitted
athrs27_force_MDI_WPL: phyAddr = (0)
PHY_FUNC_CONTROL = (862) -> (860)
MidLayer.c(1591) ML_Signal_QueueRemove :x:SIGNAL-QUEUE NOT-FOUND (tree=NORM mod=rc_wanctl_dhcpcd)
MidLayer.c(1591) ML_Signal_QueueRemove :x:SIGNAL-QUEUE NOT-FOUND (tree=NORM mod=rc_wanctl_pppoecd_0)
MidLayer.c(1591) ML_Signal_QueueRemove :x:SIGNAL-QUEUE NOT-FOUND (tree=NORM mod=rc_wanctl_pppoecd_1)
MidLayer.c(1591) ML_Signal_QueueRemove :x:SIGNAL-QUEUE NOT-FOUND (tree=NORM mod=rc_wanctl_pppoecd_2)
MidLayer.c(1591) ML_Signal_QueueRemove :x:SIGNAL-QUEUE NOT-FOUND (tree=NORM mod=rc_wanctl_pppoecd_3)
MidLayer.c(1591) ML_Signal_QueueRemove :x:SIGNAL-QUEUE NOT-FOUND (tree=NORM mod=rc_wanctl_pppoecd_4)
MidLayerModDep.c(819) startModules :INFO:Started  module rc_wanctl_pre 6394[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_wanctl_auto_detect
MidLayer.c(1591) ML_Signal_QueueRemove :x:SIGNAL-QUEUE NOT-FOUND (tree=NORM mod=rc_wanctl_dhcpcd)
MidLayerModDep.c(819) startModules :INFO:Started  module rc_wanctl_auto_detect 3072[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_wanctl_auto_detect_dummy
MidLayerModDep.c(819) startModules :INFO:Started  module rc_wanctl_auto_detect_dummy 0[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_wanctl_auto_detect_dhcpcd
MidLayerModDep.c(819) startModules :INFO:Started  module rc_wanctl_auto_detect_dhcpcd 1[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_wanctl_auto_detect_pppoecd_0
MidLayerModDep.c(819) startModules :INFO:Started  module rc_wanctl_auto_detect_pppoecd_0 0[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_wanctl_auto_detect_pppoecd_1
MidLayerModDep.c(819) startModules :INFO:Started  module rc_wanctl_auto_detect_pppoecd_1 0[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_wanctl_auto_detect_pppoecd_2
MidLayerModDep.c(819) startModules :INFO:Started  module rc_wanctl_auto_detect_pppoecd_2 0[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_wanctl_auto_detect_pppoecd_3
MidLayerModDep.c(819) startModules :INFO:Started  module rc_wanctl_auto_detect_pppoecd_3 0[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_wanctl_auto_detect_pppoecd_4
MidLayerModDep.c(819) startModules :INFO:Started  module rc_wanctl_auto_detect_pppoecd_4 0[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_wanctl_auto_detect_pppoecd_check
MidLayerModDep.c(819) startModules :INFO:Started  module rc_wanctl_auto_detect_pppoecd_check 0[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_wanctl_manual
MidLayerModDep.c(819) startModules :INFO:Started  module rc_wanctl_manual 0[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_wanctl_dhcpcd
MidLayerModDep.c(819) startModules :INFO:Started  module rc_wanctl_dhcpcd 0[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_wanctl_pppoecd_0
MidLayerModDep.c(819) startModules :INFO:Started  module rc_wanctl_pppoecd_0 0[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_wanctl_pppoecd_1
MidLayerModDep.c(819) startModules :INFO:Started  module rc_wanctl_pppoecd_1 0[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_wanctl_pppoecd_2
MidLayerModDep.c(819) startModules :INFO:Started  module rc_wanctl_pppoecd_2 0[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_wanctl_pppoecd_3
MidLayerModDep.c(819) startModules :INFO:Started  module rc_wanctl_pppoecd_3 0[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_wanctl_pppoecd_4
MidLayerModDep.c(819) startModules :INFO:Started  module rc_wanctl_pppoecd_4 0[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_wanctl_pppoecd_check
MidLayerModDep.c(819) startModules :INFO:Started  module rc_wanctl_pppoecd_check 0[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_wanctl_post
route: SIOC[ADD|DEL]RT: No such process
wanctl-lib.c(1308) CallIoctlOnEtherdeviceEx :ERR:!! Failed ioctl() !! ifr_name:[eth0] a_iCmd:[35093(-219)]:a_iCommand errorcode:126
Cannot assign requested address
MidLayerModDep.c(819) startModules :INFO:Started  module rc_wanctl_post 66[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_wanctl_pppoeroute
MidLayerModDep.c(819) startModules :INFO:Started  module rc_wanctl_pppoeroute 0[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_dnrd
wanctl-wanstate_check.c(743) wanstate_check_main :wanctl:Start wanstate_check Daemon
MidLayerModDep.c(819) startModules :INFO:Started  module rc_dnrd 10[msec]
wanctl-lib.c(4844) NtpFunctionControle :x:ntp-client disable
MidLayerModDep.c(807) startModules :INFO:Starting module rc_netwatchd
MidLayerModDep.c(819) startModules :INFO:Started  module rc_netwatchd 22[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_ipfilter
iptables: Bad rule (does a matching rule exist in that chain?)
MidLayerModDep.c(819) startModules :INFO:Started  module rc_ipfilter 311[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_ipfilter_simple
MidLayerModDep.c(819) startModules :INFO:Started  module rc_ipfilter_simple 32[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_ipfilter_user
MidLayerModDep.c(819) startModules :INFO:Started  module rc_ipfilter_user 1[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_ipfilter_pptp
MidLayerModDep.c(819) startModules :INFO:Started  module rc_ipfilter_pptp 0[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_nat
insmod: /lib/modules/2.6.31--LSDK-9.2.0.106: No such file or directory
Using /lib/modules/kernel/net/ipv4/netfilter/nf_conntrack_pptp.ko
insmod: /lib/modules/2.6.31--LSDK-9.2.0.106: No such file or directory
Using /lib/modules/kernel/net/ipv4/netfilter/nf_nat_pptp.ko
MidLayerModDep.c(819) startModules :INFO:Started  module rc_nat 218[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_routectl
MidLayerModDep.c(819) startModules :INFO:Started  module rc_routectl 20[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_plc
Using /lib/modules/kernel/drivers/char/mel_initsw.ko
insmod: cannot insert `/lib/modules/kernel/drivers/char/mel_initsw.ko': Success (17): Success
Using /lib/modules/kernel/drivers/buffalo/athsw.ko
Atheros Switch Setting Utils 0.1
killall: plc_bf: no process killed
Copyright (c)  Buffalo INC. PLC tools version 2.0(chang.aaron@gmail.com) Buile on Aug  1 2012 12:34:20

********************************************************************
Link UP phy 2 ...
Link UP phy 2, Restart autonegotiation!
athrs27_force_MDI_WPL: phyAddr = (1)
PHY_FUNC_CONTROL = (862) -> (860)
et1: unit: phy 2 not up carrier
athrs27_force_MDI_WPL: phyAddr = (3)
PHY_FUNC_CONTROL = (862) -> (860)
athrs27_force_MDI_WPL: phyAddr = (4)
PHY_FUNC_CONTROL = (862) -> (860)
MidLayerModDep.c(819) startModules :INFO:Started  module rc_plc 1130[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_lltd
MidLayerModDep.c(819) startModules :INFO:Started  module rc_lltd 112[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_wsc
Invalid command : get_stalist
Invalid command : get_stalist
MidLayerModDep.c(819) startModules :INFO:Started  module rc_wsc 590[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_upnp
*********************************************
Wi-Fi Simple Config Application - Intel Corp.
Version: Build 0.3.1d, April 24 2006
*********************************************
iptables v1.4.2: Couldn't find target `UPNP-PREROUTING-CHAIN'

Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name
iptables: No chain/target/match by that name
MidLayerModDep.c(819) startModules :INFO:Started  module rc_upnp 425[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_movie_engine
wlctl-ath.c(3398) wlconf_chg_movie_engine_profile :x:[ MOVIE_ENGINE_MODE_ON] 
athrs27_force_MDI_WPL: phyAddr = (1)
PHY_FUNC_CONTROL = (862) -> (860)
athrs27_force_MDI_WPL: phyAddr = (2)
PHY_FUNC_CONTROL = (862) -> (860)
et1: unit: phy 2 is up...
athrs27_force_MDI_WPL: phyAddr = (3)
PHY_FUNC_CONTROL = (862) -> (860)
athrs27_force_MDI_WPL: phyAddr = (4)
PHY_FUNC_CONTROL = (862) -> (860)
FUNCTION: athrs27_phy_speed, ethUnit = (1), phyUnit = (2)
ATHR_PHY_SPEED_100T!
FUNCTION: athrs27_phy_speed, ethUnit = (1), phyUnit = (2)
ATHR_PHY_SPEED_100T!
mcsnoop_br_ioctl_device:240: mcast_maxage 75000 / 250
[call extcmd]
ath0      extcmd:
[call extcmd]
ath0      extcmd:
[call extcmd]
ath0      extcmd:
set Buffalo Capability = 00000009
[call extcmd]
ath0      extcmd:
[call extcmd]
ath1      extcmd:
[call extcmd]
ath1      extcmd:
[call extcmd]
ath1      extcmd:
set Buffalo Capability = 00000009
[call extcmd]
ath1      extcmd:
[call extcmd]
ath2      extcmd:
[call extcmd]
ath2      extcmd:
[call extcmd]
ath2      extcmd:
set Buffalo Capability = 00000009
[call extcmd]
ath2      extcmd:
[call extcmd]
ath3      extcmd:
[call extcmd]
ath3      extcmd:
[call extcmd]
ath3      extcmd:
set Buffalo Capability = 00000009
[call extcmd]
ath3      extcmd:
wlctl-ath.c(3323) wlconf_modified_reset_paththrow :x:(IPv6) AS_BEHAVIOR_MODE_ROUTER
MidLayerModDep.c(819) startModules :INFO:Started  module rc_movie_engine 405[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_ntpclient
MidLayerModDep.c(819) startModules :INFO:Started  module rc_ntpclient 32[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_eco
ntp.jst.mfeed.ad.jp: Unknown host
MidLayerModDep.c(819) startModules :INFO:Started  module rc_eco 115[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_wan_qos
MidLayerModDep.c(819) startModules :INFO:Started  module rc_wan_qos 0[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_pptp_server
MidLayerModDep.c(819) startModules :INFO:Started  module rc_pptp_server 0[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_pptp_server_route
MidLayerModDep.c(819) startModules :INFO:Started  module rc_pptp_server_route 20[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_ifilter
MidLayerModDep.c(819) startModules :INFO:Started  module rc_ifilter 34[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_auto_fwup
MidLayerModDep.c(819) startModules :INFO:Started  module rc_auto_fwup 35[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_end_signal
sample: not found
MidLayerModDep.c(819) startModules :INFO:Started  module rc_end_signal 72[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_timer_reboot
MidLayerModDep.c(819) startModules :INFO:Started  module rc_timer_reboot 0[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_dst_timer
MidLayerModDep.c(819) startModules :INFO:Started  module rc_dst_timer 0[msec]
athrs27_force_MDI_WPL: phyAddr = (1)
PHY_FUNC_CONTROL = (862) -> (860)
et1: unit: phy 2 not up carrier
athrs27_force_MDI_WPL: phyAddr = (3)
PHY_FUNC_CONTROL = (862) -> (860)
athrs27_force_MDI_WPL: phyAddr = (4)
PHY_FUNC_CONTROL = (862) -> (860)
Initializing stack... OK
Now starting stack
athrs27_force_MDI_WPL: phyAddr = (1)
PHY_FUNC_CONTROL = (862) -> (860)
athrs27_force_MDI_WPL: phyAddr = (2)
PHY_FUNC_CONTROL = (862) -> (860)
et1: unit: phy 2 is up...
athrs27_force_MDI_WPL: phyAddr = (3)
PHY_FUNC_CONTROL = (862) -> (860)
athrs27_force_MDI_WPL: phyAddr = (4)
PHY_FUNC_CONTROL = (862) -> (860)
FUNCTION: athrs27_phy_speed, ethUnit = (1), phyUnit = (2)
ATHR_PHY_SPEED_100T!
FUNCTION: athrs27_phy_speed, ethUnit = (1), phyUnit = (2)
ATHR_PHY_SPEED_100T!
DEVICE PIN: 27060483

******* MODE: AP with built-in Registrar and UPnP Proxy *******

checking for PUSH BUTTON
devpwd is not setted, but start InitiateRegistrarion.
Waiting for Client to connect(using IEs)...
ARPING to 192.168.11.1 from 192.168.11.1 via br0
Sent 1 probes (1 broadcast(s))
Received 0 reply



BusyBox v1.00 (2012.08.01-03:34+0000) Built-in shell (msh)
Enter 'help' for a list of built-in commands.

#