WSR-600DHPのシリアル接続
2016年5月 3日(火) 10:03 JST
閲覧数 3,522
なんか順番が逆な気もしますが、WSR-600DHPのシリアル接続についてです。
電源再起動できないとかさまざまな現象が発生するので、シリアル接続は出来るぐらいのつもりで居た方がいいでしょう。
回路追ってないので原因解りませんが。。。(この板にこだわる必要がないので追う必要性が低い)
シリアルの結線は、写真上側からRX、TX、GND、VCC。57600bps
ピンは立ってないので、自分で立てる必要がある。テストワイヤーでもいいけど。
大部分がカバーで覆われていて剥がすのはめんどくさい。
搭載SoCはMT7621S。1コア2スレッドタイプ。
起動時の出力をペロッと貼り付け。
DualImageモードを使用しているので、書換えとかオリジナルへの戻しとかめんどくさい。
電源再起動できないとかさまざまな現象が発生するので、シリアル接続は出来るぐらいのつもりで居た方がいいでしょう。
回路追ってないので原因解りませんが。。。(この板にこだわる必要がないので追う必要性が低い)
シリアルの結線は、写真上側からRX、TX、GND、VCC。57600bps
ピンは立ってないので、自分で立てる必要がある。テストワイヤーでもいいけど。
大部分がカバーで覆われていて剥がすのはめんどくさい。
搭載SoCはMT7621S。1コア2スレッドタイプ。
起動時の出力をペロッと貼り付け。
DualImageモードを使用しているので、書換えとかオリジナルへの戻しとかめんどくさい。
===================================================================
MT7621 stage1 code 13:14:00 (ASIC)
CPU=50000000 HZ BUS=12500000 HZ
==================================================================
Change MPLL source from XTAL to CR...
do MEMPLL setting..
MEMPLL Config : 0x31000000
3PLL mode + External loopback
=== XTAL-40Mhz === DDR-800Mhz ===
PLL3 FB_DL: 0x13, 1/0 = 608/416 4D000000
PLL4 FB_DL: 0x18, 1/0 = 563/461 61000000
PLL2 FB_DL: 0x1e, 1/0 = 600/424 79000000
do DDR setting..[00320000]
Apply DDR2 Setting...(use default AC)
0 8 16 24 32 40 48 56 64 72 80 88 96 104 112 120
--------------------------------------------------------------------------------
0000:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0001:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0002:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0003:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0004:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0005:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0006:| 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1
0007:| 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1
0008:| 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0
0009:| 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0
000A:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
000B:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
000C:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
000D:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
000E:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
000F:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0010:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0011:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0012:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0013:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0014:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0015:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0016:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0017:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0018:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0019:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
001A:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
001B:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
001C:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
001D:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
001E:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
001F:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
rank 0 coarse = 8
rank 0 fine = 48
B:| 0 0 0 0 0 0 0 1 1 1 0 0 0 0 0 0
opt_dle value:8
DRAMC_R0DELDLY[018]=00002B2B
==================================================================
RX DQS perbit delay software calibration
==================================================================
1.0-15 bit dq delay value
==================================================================
bit| 0 1 2 3 4 5 6 7 8 9
--------------------------------------
0 | 7 6 8 8 5 4 5 4 7 6
10 | 10 7 7 10 7 10
--------------------------------------
==================================================================
2.dqs window
x=pass dqs delay value (min~max)center
y=0-7bit DQ of every group
input delay:DQS0 =43 DQS1 = 43
==================================================================
bit DQS0 bit DQS1
0 (1~85)43 8 (1~84)42
1 (1~85)43 9 (1~84)42
2 (1~86)43 10 (1~84)42
3 (1~82)41 11 (1~82)41
4 (1~84)42 12 (1~85)43
5 (1~82)41 13 (1~85)43
6 (1~78)39 14 (1~86)43
7 (1~84)42 15 (1~86)43
==================================================================
3.dq delay value last
==================================================================
bit| 0 1 2 3 4 5 6 7 8 9
--------------------------------------
0 | 7 6 8 10 6 6 9 5 8 7
10 | 11 9 7 10 7 10
==================================================================
==================================================================
TX perbyte calibration
==================================================================
DQS loop = 15, cmp_err_1 = ffff0000
dqs_perbyte_dly.last_dqsdly_pass[0]=15, finish count=1
dqs_perbyte_dly.last_dqsdly_pass[1]=15, finish count=2
DQ loop=15, cmp_err_1 = ffff0000
dqs_perbyte_dly.last_dqdly_pass[0]=15, finish count=1
dqs_perbyte_dly.last_dqdly_pass[1]=15, finish count=2
byte:0, (DQS,DQ)=(8,8)
byte:1, (DQS,DQ)=(8,8)
20,data:88
[EMI] DRAMC calibration passed
===================================================================
MT7621 stage1 code done
CPU=50000000 HZ BUS=12500000 HZ
===================================================================
U-Boot 1.1.3 (Aug 14 2014 - 22:05:54)
Board: Ralink APSoC DRAM: 64 MB
relocate_code Pointer at: 83fb8000
Config XHCI 40M PLL
******************************
Software System Reset Occurred
******************************
flash manufacture id: ef, device id 40 18
find flash: W25Q128BV
============================================
Ralink UBoot Version: 4.2.1.0
Buffalo UBoot Version: 1.03
--------------------------------------------
ASIC 7621_MP (MAC to MT7530 Mode)
DRAM_CONF_FROM: Auto-Detection
DRAM_TYPE: DDR2
DRAM bus: 16 bit
Xtal Mode=3 OCP Ratio=1/4
Flash component: 16 MBytes NOR Flash
Date:Aug 14 2014 Time:22:05:54
============================================
icache: sets:256, ways:4, linesz:32 ,total:32768
dcache: sets:256, ways:4, linesz:32 ,total:32768
##### The CPU freq = 880 MHZ ####
estimate memory size =64 Mbytes
#Reset_MT7530
set LAN/WAN LLLLW
aossgpio=[262144]
Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
7: Load Boot Loader code then write to Flash via Serial.
9: Load Boot Loader code then write to Flash via TFTP.
0
3: System Boot system code via Flash.
=================================================
Check image validation:
Image1 Header Magic Number --> OK
Image2 Header Magic Number --> OK
Image1 Header Checksum --> OK
Image2 Header Checksum --> OK
Image1 Data Checksum --> OK
Image2 Data Checksum --> OK
Image1: OK Image2: OK
Check if Image1 and Image2's Checksum are the same:
Two Images are the same
=================================================
Erasing SPI Flash...
.
Writing to SPI Flash...
.
done
## Booting image at bfc50000 ...
Image Name: Linux Kernel Image
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 6085928 Bytes = 5.8 MB
Load Address: 80001000
Entry Point: 8000d1d0
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 8000d1d0) ...
## Giving linux memsize in MB, 64
Starting kernel ...
LINUX started...
THIS IS ASIC
Linux version 2.6.36 (root@SWD1-CVS3) (gcc version 4.6.3 (Buildroot 2012.11.1) ) #1 SMP Wed Apr 6 19:17:57 CST 2016
The CPU feqenuce set to 880 MHz
GCMP present
CPU revision is: 0001992f (MIPS 1004Kc)
Software DMA cache coherency
Determined physical RAM map:
memory: 04000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
Normal 0x00000000 -> 0x00004000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0x00000000 -> 0x00004000
avail: cpu2 is not ready
avail: cpu3 is not ready
Detected 1 available secondary CPU(s)
PERCPU: Embedded 7 pages/cpu @81083000 s6464 r8192 d14016 u65536
pcpu-alloc: s6464 r8192 d14016 u65536 alloc=16*4096
pcpu-alloc: [0] 0 [0] 1
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
Kernel command line: console=ttyS1,57600n8 root=/dev/ram0 console=ttyS1,57600 root=/dev/ram0 rootfstype=squashfs,jffs2
PID hash table entries: 256 (order: -2, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Primary instruction cache 32kB, VIPT, , 4-waylinesize 32 bytes.
Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
Writing ErrCtl register=000506c0
Readback ErrCtl register=000506c0
Memory: 55432k/65536k available (3708k kernel code, 10104k reserved, 1036k data, 4416k init, 0k highmem)
Hierarchical RCU implementation.
Verbose stalled-CPUs detection is disabled.
NR_IRQS:128
Trying to install interrupt handler for IRQ24
Trying to install interrupt handler for IRQ25
Trying to install interrupt handler for IRQ22
Trying to install interrupt handler for IRQ9
Trying to install interrupt handler for IRQ10
Trying to install interrupt handler for IRQ11
Trying to install interrupt handler for IRQ12
Trying to install interrupt handler for IRQ13
Trying to install interrupt handler for IRQ14
Trying to install interrupt handler for IRQ16
Trying to install interrupt handler for IRQ17
Trying to install interrupt handler for IRQ18
Trying to install interrupt handler for IRQ19
Trying to install interrupt handler for IRQ20
Trying to install interrupt handler for IRQ21
Trying to install interrupt handler for IRQ23
Trying to install interrupt handler for IRQ26
Trying to install interrupt handler for IRQ27
Trying to install interrupt handler for IRQ28
Trying to install interrupt handler for IRQ15
Trying to install interrupt handler for IRQ8
Trying to install interrupt handler for IRQ29
Trying to install interrupt handler for IRQ30
Trying to install interrupt handler for IRQ31
CPU0: status register was 11000000
CPU0: status register now 11000000
CPU0: status register frc 11001800
console [ttyS1] enabled
Calibrating delay loop... 579.58 BogoMIPS (lpj=1159168)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
launch: starting cpu1
launch: cpu1 gone!
CPU revision is: 0001992f (MIPS 1004Kc)
Primary instruction cache 32kB, VIPT, , 4-waylinesize 32 bytes.
Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
Brought up 2 CPUs
Synchronize counters across 2 CPUs: done.
NET: Registered protocol family 16
release PCIe RST: RALINK_RSTCTRL = 7000000
PCIE PHY initialize
***** Xtal 40MHz *****
start MT7621 PCIe register access
RALINK_RSTCTRL = 7000000
RALINK_CLKCFG1 = 77ffeff8
*************** MT7621 PCIe RC mode *************
PCIE2 no card, disable it(RST&CLK)
pcie_link status = 0x3
RALINK_RSTCTRL= 3000000
*** Configure Device number setting of Virtual PCI-PCI bridge ***
RALINK_PCI_PCICFG_ADDR = 21007f2 -> 21007f2
PCIE0 enabled
PCIE1 enabled
interrupt enable status: 300000
Port 1 N_FTS = 1b105000
Port 0 N_FTS = 1b105000
config reg done
init_rt2880pci done
bio: create slab at 0
vgaarb: loaded
SCSI subsystem initialized
pci 0000:00:00.0: BAR 0: can't assign mem (size 0x80000000)
pci 0000:00:01.0: BAR 0: can't assign mem (size 0x80000000)
pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff]
pci 0000:00:01.0: BAR 8: assigned [mem 0x60100000-0x601fffff]
pci 0000:00:00.0: BAR 1: assigned [mem 0x60200000-0x6020ffff]
pci 0000:00:00.0: BAR 1: set to [mem 0x60200000-0x6020ffff] (PCI address [0x60200000-0x6020ffff]
pci 0000:00:01.0: BAR 1: assigned [mem 0x60210000-0x6021ffff]
pci 0000:00:01.0: BAR 1: set to [mem 0x60210000-0x6021ffff] (PCI address [0x60210000-0x6021ffff]
pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x6000ffff]
pci 0000:01:00.0: BAR 0: set to [mem 0x60000000-0x6000ffff] (PCI address [0x60000000-0x6000ffff]
pci 0000:00:00.0: PCI bridge to [bus 01-01]
pci 0000:00:00.0: bridge window [io disabled]
pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff]
pci 0000:00:00.0: bridge window [mem pref disabled]
pci 0000:02:00.0: BAR 0: assigned [mem 0x60100000-0x601fffff]
pci 0000:02:00.0: BAR 0: set to [mem 0x60100000-0x601fffff] (PCI address [0x60100000-0x601fffff]
pci 0000:00:01.0: PCI bridge to [bus 02-02]
pci 0000:00:01.0: bridge window [io disabled]
pci 0000:00:01.0: bridge window [mem 0x60100000-0x601fffff]
pci 0000:00:01.0: bridge window [mem pref disabled]
BAR0 at slot 0 = 0
bus=0x0, slot = 0x0
res[0]->start = 0
res[0]->end = 0
res[1]->start = 60200000
res[1]->end = 6020ffff
res[2]->start = 0
res[2]->end = 0
res[3]->start = 0
res[3]->end = 0
res[4]->start = 0
res[4]->end = 0
res[5]->start = 0
res[5]->end = 0
BAR0 at slot 1 = 0
bus=0x0, slot = 0x1
res[0]->start = 0
res[0]->end = 0
res[1]->start = 60210000
res[1]->end = 6021ffff
res[2]->start = 0
res[2]->end = 0
res[3]->start = 0
res[3]->end = 0
res[4]->start = 0
res[4]->end = 0
res[5]->start = 0
res[5]->end = 0
bus=0x1, slot = 0x0, irq=0x4
res[0]->start = 60000000
res[0]->end = 6000ffff
res[1]->start = 0
res[1]->end = 0
res[2]->start = 0
res[2]->end = 0
res[3]->start = 0
res[3]->end = 0
res[4]->start = 0
res[4]->end = 0
res[5]->start = 0
res[5]->end = 0
bus=0x2, slot = 0x1, irq=0x18
res[0]->start = 60100000
res[0]->end = 601fffff
res[1]->start = 0
res[1]->end = 0
res[2]->start = 0
res[2]->end = 0
res[3]->start = 0
res[3]->end = 0
res[4]->start = 0
res[4]->end = 0
res[5]->start = 0
res[5]->end = 0
Switching to clocksource MIPS
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
UDP hash table entries: 128 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 128 (order: 0, 4096 bytes)
NET: Registered protocol family 1
4 CPUs re-calibrate udelay(lpj = 1167360)
squashfs: version 4.0 (2009/01/31) Phillip Lougher
JFFS2 version 2.2 (NAND) (SUMMARY) (ZLIB) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
fuse init (API version 7.15)
msgmni has been set to 108
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered (default)
HDLC line discipline maxframe=4096
N_HDLC line discipline registered.
Ralink gpio driver initialized
Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x1e000d00 (irq = 27) is a 16550A
serial8250: ttyS1 at MMIO 0x1e000c00 (irq = 26) is a 16550A
brd: module loaded
flash manufacture id: ef, device id 40 18
W25Q128BV(ef 40180000) (16384 Kbytes)
mtd .name = raspi, .size = 0x01000000 (16M) .erasesize = 0x00010000 (64K) .numeraseregions = 0
Creating 6 MTD partitions on "raspi":
0x000000000000-0x000000030000 : "Bootloader"
0x000000030000-0x000000040000 : "Config"
0x000000040000-0x000000050000 : "Factory"
0x000000050000-0x000000700000 : "Kernel"
0x000000700000-0x000000800000 : "User_CFG"
0x000000850000-0x000000f00000 : "Kernel2"
rdm_major = 253
GMAC1_MAC_ADRH -- : 0x0000000c
GMAC1_MAC_ADRL -- : 0x43288056
Ralink APSoC Ethernet Driver Initilization. v3.1 512 rx/tx descriptors allocated, mtu = 1500!
GMAC1_MAC_ADRH -- : 0x0000000c
GMAC1_MAC_ADRL -- : 0x43288021
PROC INIT OK!
PPP generic driver version 2.4.2
PPP BSD Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
register mt_drv
=== pAd = c0282000, size = 1006384 ===
<-- RTMPAllocTxRxRingMemory, Status=0
<-- RTMPAllocAdapterBlock, Status=0
pAd->CSRBaseAddress =0xc0180000, csr_addr=0xc0180000!
device_id =0x7603
RtmpChipOpsHook(502): Not support for HIF_MT yet!
mt7603_init()-->
mt_bcn_buf_init(224): Not support for HIF_MT yet!
<--mt7603_init()
Ralink APSoC Hardware Watchdog Timer
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (866 buckets, 3464 max)
ctnetlink v0.93: registering with nfnetlink.
xt_time: kernel timezone is -0000
IPVS: Registered protocols ()
IPVS: Connection hash table configured (size=4096, memory=32Kbytes)
IPVS: ipvs loaded.
ip_tables: (C) 2000-2006 Netfilter Core Team, Type=Restricted Cone
TCP cubic registered
NET: Registered protocol family 17
create_proc_read_write_entry: fail
L2TP core driver, V2.0
PPPoL2TP kernel driver, V2.0
802.1Q VLAN Support v1.8 Ben Greear
All bugs added by David S. Miller
Freeing unused kernel memory: 4416k freed
init started: BusyBoxAlgorithmics/MIPS FPU Emulator v1.5
v1.12.1 (2016-04-06 19:10:44 CST)
starting pidled=12, on=10, off=10, blinks,=4000, reset=1, time=4000
36, tty '': '/etc_ro/rcS'
devpts: called with bogus options
mount: mounting none on /proc/bus/usb failed: No such file or directory
Welcome to
_______ _______ ___ __ ____ _ _ ___
| ___ \| __ || | |__|| \ | || | / /
| |___| || |__| || |__ __ | \| || |/ /
| _ /| _ || || || |\ || \
|__| \__\|__| |__||______||__||_| \____||_|\___\
=System Architecture Department=
[check_jffs]80 : JFFS_OK
nvram_init: INFO=>nvram MAC initialized successfully!
==>shm_init()!!
check_shm_hash: Check shm hash value
nvram_init: INFO=>nvram conf initialized successfully!
nvram_init: INFO=> RAM CONF successful created!
nvram_init: INFO=> RC.CONF successful created!
---------------- Get WLAN MAC cc:e1:d5:0b:7b:7e---------------
Tue Jan 1 00:00:00 GMT 2013
led=45, on=1, off=4000, blinks,=1, reset=1, time=4000
led=46, on=4000, off=1, blinks,=1, reset=1, time=4000
switch reg write offset=2004, value=ff0003
switch reg write offset=2104, value=ff0003
switch reg write offset=2204, value=ff0003
switch reg write offset=2304, value=ff0003
switch reg write offset=2404, value=ff0003
switch reg write offset=2504, value=ff0003
switch reg write offset=2010, value=810000c0
switch reg write offset=2110, value=810000c0
switch reg write offset=2210, value=810000c0
switch reg write offset=2310, value=810000c0
switch reg write offset=2410, value=810000c0
switch reg write offset=2510, value=810000c0
switch reg write offset=2610, value=81000000
switch reg write offset=2710, value=81000000
switch reg write offset=2604, value=20ff0003
switch reg write offset=2704, value=20ff0003
Special Tag Disabled
switch reg write offset=2610, value=81000000
switch reg write offset=2014, value=10001
switch reg write offset=2114, value=10001
switch reg write offset=2214, value=10001
switch reg write offset=2314, value=10001
switch reg write offset=2414, value=10002
switch reg write offset=2514, value=10001
REG_ESW_WT_MAC_ATC is 0x7ff0002
done.
input_access=[3]
echo 3 > /proc/lan_wlan_access_controller
port_bridge_on: mac_string=[cce1d50b7b7e]
port_bridge_on: pbcmd=[switch add cce1d50b7b7e 00000010 2]
REG_ESW_WT_MAC_ATA1 is 0xcce1d50b
REG_ESW_WT_MAC_ATA2 is 0x7b7e8002
REG_ESW_WT_MAC_ATWD is 0xff00040c
done.
getbootloaderenv : bootloader_ver =1.03
rmmod: ipv6passthru: No such file or directory
rmmod: ipv6passthru: No such file or directory
/usr/shell/dnsmasq.sh stop ok
/usr/shell/dnsmasq.sh start ok
/usr/shell/udhcpd.sh config ok
/usr/shell/udhcpd.sh start ok
START add route..............
***** g_wl_interface = ra0 ******
MAX_NUM_SESSIONS : 5; NUM_SEES: 64
cp: cannot stat '/etc_ro/Wireless/RT2860AP/JP.dat': No such file or directory
rm: cannot remove '/tmp/wsc_dual_a': No such file or directory
rm: cannot remove '/tmp/wsc_dual_g': No such file or directory
psntpdate: Resource temporarily unavailable
=== psntpdate: checkntp_gettime=0 ===
brctl setwlanforward br0 15 15
Interface doesn't accept private ioctl...
set (8BE2): Network is down
ioctl error
ioctl error
ioctl error
brctl setwlanforward br0 15 15
killall: wlan_led_ctrl: no process killed
[Enter Test] in wlan_led_ctrl.c main()
.Unknown option: -I
Unknown option: ra0
route: ioctl 0x890c failed: No such process
/usr/shell/staticip.sh stop ok
route: ioctl 0x890c failed: No such process
/usr/shell/udhcpc.sh stop ok
killall: internet_chk: no process killed
killall: tproxy: no process killed
iptables: No chain/target/match by that name.
iptables v1.4.10: Couldn't load target `IFILTER':File not found
Try `iptables -h' or 'iptables --help' for more information.
rmmod: hw_nat: No such file or directory
hn d
====Auto Switch: Enter CHECK_WAN_LINK state====
====Auto Switch: WAN_LINK is offline!====
====Auto Switch: Enter CHECK_LAN_LINK state====
====Auto Switch: LAN_LINK is offline!====
START add route..............
killall: pptpd: no process killed
killall: online_fw_notifier: no process killed
===== Auto FW Update: online_fw_notifier starts ! =====
CAN'T FIND AutoFwUpdateStart
CAN'T FIND AutoFwUpdateCheckStart
CAN'T FIND FwUpdateCheckFinish
CAN'T FIND FwConfirmUpdate
CAN'T FIND InternetStartFinish
===== Auto FW Update: Time to get firmware list = 6 : 55 =====
===== Auto FW Update: Time to update firmware = 4 : 55 =====
CAN'T FIND GetFwListTime
CAN'T FIND UpdateFwTime
starting pid 9475, tty '/dev/ttyS1': '/bin/sh'
BusyBox v1.12.1 (2016-04-06 19:10:44 CST) built-in shell (ash)
Enter 'help' for a list of built-in commands.
# killall: psntpdate: no process killed
killall: psntpdate: no process killed
CAN'T FIND CurrentFwVersion
CAN'T FIND AutoFwUpdateUserAgent
AutoFwUpdateUserAgent = "BuffaloBBS%WSR-600DHP-JP%ne1QWTLsx9EJBlUm3HH8h0Xs3sn1ufvf%2.20%aak0%4d69a7d7696101c82becddb6e467b38e"
Delete disconnect dynamic client 5c:f9:dd:65:57:d2
psntpdate: Resource temporarily unavailable
=== psntpdate: checkntp_gettime=0 ===
killall: psntpdate: no process killed
