Roseapple Pi到着。
2016年4月 4日(月) 19:51 JST
閲覧数 13,420
発送が遅れていたRoseapple Piですが到着しました。
Roseapple Piと言っても初めて聞く人も多いだろう。
プロジェクトが立ち上がった時はLemon Piという名前だった為、こちらの名前には記憶のある方も居るかと思う。
Indiegogoで出資を募っていたプロジェクトだが、少し時間が掛った事もあり、コアがCortex-A9と少し古さを感じてしまう状態となってしまったが、USB 3.0搭載だったりメモリが2GB搭載だったりと、ある方面では魅力負けしていない板の一つではあると思われる。
箱は、白箱にシールを片面貼っただけのシンプルな構成。
Orange Pi等、箱まで印刷して出してきている板が増えたので、安っぽい感じは否めない。(そこを求めるのは間違っているのだろうが)
おそらく、スペックも何も知られていないと思われるので基板を見つつ、スペックも記載しておきます。
コア自体はCortex-A9という事で、少し物足りなさを覚えますが、板全体としてのスペックは悪くありません。
メモリ2GBが良く効いていて、他の板でしんどかった箇所に手の届く板となっていると思います。
SoCにはヒートシンクが初めから着いています。
この類の安価な板では、ヒートシンクは自分で着けるか判断する事が多いので、初めからついているのは少ないです。
実際、発熱はかなりあるので着いててよかったという所です。
スペックを見ていきますが、USB 3.0搭載とメモリ 2GB搭載は大きな利点になります。
Ethernetが100Mbpsなのが残念ですが、USB 3.0で補える可能性は高いです。
基板裏面ですが、WiFiチップを搭載するパターンも存在しており、今後にも期待できそうです。
日本で使う範囲では、WiFiチップが無い方が技適の関係から安心ではあるのですが。。。
全体としては綺麗な出来だと思うのですが、少し配線パターンが僕好みではない箇所があるのは黙っておこう。
やはり、USB 3.0搭載という点は正直嬉しい。
USB 2.0ではどうしても遅いので、どれぐらい速度が出てくれるかが気になる処。
SATA搭載のSoCも無くなってきているのでUSB 3.0搭載は貴重です。(これからUSB 3.0搭載は増える筈だが、まだまだ2.0止まりなので)
とりあえず、Debianのイメージで起動させました。
ペンギンが4匹ならぶのではなく、地球ロゴ？が4個並びました。
UpdateしないとGPUが上手く機能していないのか、もっさり感がある。
コアがCortex-A9なのが少し残念だが、決して遅い訳ではない。
Roseapple Piと言っても初めて聞く人も多いだろう。
プロジェクトが立ち上がった時はLemon Piという名前だった為、こちらの名前には記憶のある方も居るかと思う。
Indiegogoで出資を募っていたプロジェクトだが、少し時間が掛った事もあり、コアがCortex-A9と少し古さを感じてしまう状態となってしまったが、USB 3.0搭載だったりメモリが2GB搭載だったりと、ある方面では魅力負けしていない板の一つではあると思われる。
箱は、白箱にシールを片面貼っただけのシンプルな構成。
Orange Pi等、箱まで印刷して出してきている板が増えたので、安っぽい感じは否めない。(そこを求めるのは間違っているのだろうが)
おそらく、スペックも何も知られていないと思われるので基板を見つつ、スペックも記載しておきます。
コア自体はCortex-A9という事で、少し物足りなさを覚えますが、板全体としてのスペックは悪くありません。
メモリ2GBが良く効いていて、他の板でしんどかった箇所に手の届く板となっていると思います。
SoCにはヒートシンクが初めから着いています。
この類の安価な板では、ヒートシンクは自分で着けるか判断する事が多いので、初めからついているのは少ないです。
実際、発熱はかなりあるので着いててよかったという所です。
スペックを見ていきますが、USB 3.0搭載とメモリ 2GB搭載は大きな利点になります。
Ethernetが100Mbpsなのが残念ですが、USB 3.0で補える可能性は高いです。
| SoC | Actions-semi S500 (Cortex-A9 QuadCore) |
| GPU | PowerVR SGX544 |
| Memory | 2GB DDR3 |
| Storage | MicroSD |
| Network | 10/100Mbps |
| Video | HDMI1.4 with HDCP |
| USB | USB 3.0 x1, USB 2.0 x2 |
基板裏面ですが、WiFiチップを搭載するパターンも存在しており、今後にも期待できそうです。
日本で使う範囲では、WiFiチップが無い方が技適の関係から安心ではあるのですが。。。
全体としては綺麗な出来だと思うのですが、少し配線パターンが僕好みではない箇所があるのは黙っておこう。
やはり、USB 3.0搭載という点は正直嬉しい。
USB 2.0ではどうしても遅いので、どれぐらい速度が出てくれるかが気になる処。
SATA搭載のSoCも無くなってきているのでUSB 3.0搭載は貴重です。(これからUSB 3.0搭載は増える筈だが、まだまだ2.0止まりなので)
とりあえず、Debianのイメージで起動させました。
ペンギンが4匹ならぶのではなく、地球ロゴ？が4個並びました。
UpdateしないとGPUが上手く機能していないのか、もっさり感がある。
コアがCortex-A9なのが少し残念だが、決して遅い訳ではない。
linaro@localhost:~$ cat /proc/cpuinfo Processor : ARMv7 Processor rev 1 (v7l) processor : 0 model name : ARMv7 Processor rev 1 (v7l) BogoMIPS : 1835.17 Features : swp half thumb fastmult vfp edsp thumbee neon vfpv3 tls CPU implementer : 0x41 CPU architecture: 7 CPU variant : 0x4 CPU part : 0xc09 CPU revision : 1 processor : 1 model name : ARMv7 Processor rev 1 (v7l) BogoMIPS : 1835.17 Features : swp half thumb fastmult vfp edsp thumbee neon vfpv3 tls CPU implementer : 0x41 CPU architecture: 7 CPU variant : 0x4 CPU part : 0xc09 CPU revision : 1 processor : 2 model name : ARMv7 Processor rev 1 (v7l) BogoMIPS : 1835.17 Features : swp half thumb fastmult vfp edsp thumbee neon vfpv3 tls CPU implementer : 0x41 CPU architecture: 7 CPU variant : 0x4 CPU part : 0xc09 CPU revision : 1 processor : 3 model name : ARMv7 Processor rev 1 (v7l) BogoMIPS : 1835.17 Features : swp half thumb fastmult vfp edsp thumbee neon vfpv3 tls CPU implementer : 0x41 CPU architecture: 7 CPU variant : 0x4 CPU part : 0xc09 CPU revision : 1 Hardware : gs705a Revision : 0000 Serial : 080a46316d0f4c1b起動ログ。
linaro@localhost:~$ dmesg
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Linux version 3.10.37 (build@bs.dev.linux-xapple.org) (gcc version 4.8.2 (Ubuntu/Linaro 4.8.2-16ubuntu4) ) #1 SMP PREEMPT Sat Nov 21 10:33:56 CST 2015
[ 0.000000] CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c53c7d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine: gs705a, model: Actions GS705A board
[ 0.000000] owl_reserve: pyhsical memory size 2147483648 bytes, end @0x2f800000
[ 0.000000] find owl_fb_size=0x800000
[ 0.000000] find owl_kinfo_size=0x100000
[ 0.000000] find owl_ion0_size=0x100000
[ 0.000000] find owl_ion1_size=0xc000000
[ 0.000000] ion_reserve: ion_fb reserved base 2ee00000 size 1048576
[ 0.000000] Reserved memory 193MB
[ 0.000000] FB: 0x2f000000, 8MB
KINFO: 0x2ef00000, 1MB
ION0: 0x2ee00000, 1MB
ION1: 0x22e00000, 192MB
[ 0.000000] cma: CMA: reserved 192 MiB at 22c00000
[ 0.000000] Memory policy: ECC disabled, Data cache writealloc
[ 0.000000] On node 0 totalpages: 524288
[ 0.000000] free_area_init_node: node 0, pgdat c0b07380, node_mem_map c0c69000
[ 0.000000] Normal zone: 1520 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 194560 pages, LIFO batch:31
[ 0.000000] HighMem zone: 2576 pages used for memmap
[ 0.000000] HighMem zone: 329728 pages, LIFO batch:31
[ 0.000000] owl_smp_init_cpus(): ncores 4
[ 0.000000] PERCPU: Embedded 9 pages/cpu @c1c81000 s13824 r8192 d14848 u36864
[ 0.000000] pcpu-alloc: s13824 r8192 d14848 u36864 alloc=9*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 522768
[ 0.000000] Kernel command line: console=ttyS2 console=tty0 root=/dev/mmcblk0p3 rootwait ro androidboot.dvfslevel=0x705x androidboot.bootdev=sd boot_dev=sd0
[ 0.000000] boot_mode_process
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] allocated 4194304 bytes of page_cgroup
[ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[ 0.000000] Memory: 2048MB = 2048MB total
[ 0.000000] Memory: 1841248k/1841248k available, 255904k reserved, 1318912K highmem
[ 0.000000] Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
vmalloc : 0xf0000000 - 0xff000000 ( 240 MB)
lowmem : 0xc0000000 - 0xef800000 ( 760 MB)
pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
.text : 0xc0008000 - 0xc0a286e0 (10370 kB)
.init : 0xc0a29000 - 0xc0a99600 ( 450 kB)
.data : 0xc0a9a000 - 0xc0b1f4c4 ( 534 kB)
.bss : 0xc0b1f4c4 - 0xc0c68184 (1316 kB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] NR_IRQS:247
[ 0.000000] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] console [tty0] enabled
[ 0.000000] kmemleak: Kernel memory leak detector disabled
[ 0.001035] Calibrating delay loop... 1196.85 BogoMIPS (lpj=5984256)
[ 0.090239] pid_max: default: 32768 minimum: 301
[ 0.090482] Security Framework initialized
[ 0.090552] SELinux: Initializing.
[ 0.090665] SELinux: Starting in permissive mode
[ 0.090683] AppArmor: AppArmor disabled by boot time parameter
[ 0.090808] Mount-cache hash table entries: 512
[ 0.098981] Initializing cgroup subsys debug
[ 0.099034] Initializing cgroup subsys memory
[ 0.099105] Initializing cgroup subsys freezer
[ 0.099195] CPU: Testing write buffer coherency: ok
[ 0.099826] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.099900] owl_smp_prepare_cpus(max_cpus:4)
[ 0.100006] Setting up static identity map for 0xc07359c0 - 0xc0735a80
[ 0.100092] owl_l2x0_init()
[ 0.100202] L310 cache controller enabled
[ 0.100227] l2x0: 16 ways, CACHE_ID 0x410080c9, AUX_CTRL 0x3e050000, Cache size: 524288 B
[ 0.140182] ftrace: Allocated trace_printk buffers
[ 0.144743] cpu:1
[ 0.144772] po 1
[ 0.144989] wu 1
[ 0.145776] CPU1: Booted secondary processor
[ 0.145783] pr:-1
[ 0.179915] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.200651] cpu:2
[ 0.200692] po 2
[ 0.200971] wu 2
[ 0.201741] CPU2: Booted secondary processor
[ 0.201748] pr:-1
[ 0.239913] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002
[ 0.260673] cpu:3
[ 0.260713] po 3
[ 0.260992] wu 3
[ 0.261764] CPU3: Booted secondary processor
[ 0.261771] pr:-1
[ 0.299914] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003
[ 0.300071] Brought up 4 CPUs
[ 0.300111] SMP: Total of 4 processors activated (4787.40 BogoMIPS).
[ 0.300131] CPU: All CPU(s) started in SVC mode.
[ 0.301344] devtmpfs: initialized
[ 0.306500] pinctrl core: initialized pinctrl subsystem
[ 0.306962] regulator-dummy: no parameters
[ 0.314391] NET: Registered protocol family 16
[ 0.348225] DMA: preallocated 14336 KiB pool for atomic coherent allocations
[ 0.348269] init sirqs
[ 0.348347] owl_gpio_init()
[ 0.350746] owl_gpio_probe()
[ 0.350775] owl gpio bank0 - irq68
[ 0.350794] owl gpio bank1 - irq69
[ 0.350810] owl gpio bank2 - irq70
[ 0.350826] owl gpio bank3 - irq71
[ 0.350842] owl gpio bank4 - irq72
[ 0.351686] owl_sirq_probe()
[ 0.351709] owl sirq bank0 - irq45
[ 0.351727] owl sirq bank1 - irq46
[ 0.351743] owl sirq bank2 - irq47
[ 0.351769] sirq map 45 -> 213
[ 0.351791] sirq map 46 -> 214
[ 0.351813] sirq map 47 -> 215
[ 0.354400] owl_board_init()
[ 0.354445] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
[ 0.354475] hw-breakpoint: maximum watchpoint size is 4 bytes.
[ 0.354732] free reserve pages 256 to buddy system
[ 0.354753] owl_common_init()
[ 0.354857] [PowerGate] name: 'dma', on: 0, before SPS_PG_CTL: 0x703360
[ 0.354883] [PowerGate] name: 'dma', on: 0, after SPS_PG_CTL: 0x703260
[ 0.355597] pwm-owl b01b0050.pwm: Probing...
[ 0.355842] dmm debugfs support
[ 0.359837] i2c i2c-2: of_i2c: invalid reg on /i2c@b0178000/mpu6515@68
[ 0.371918] bio: create slab at 0
[ 0.372910] owl_pwm_bl_probe: name = backlight.2
[ 0.373094] owl pinctrl: 1gpio_request_check_pinmux
[ 0.373120] owl pinctrl: 1CHECK PMX:P_I2C1_SCLK has already been requested by b0174000.i2cowl_dma_init
[ 0.373457] owl_dma_probe
[ 0.373494] [PowerGate] name: 'dma', on: 1, before SPS_PG_CTL: 0x702260
[ 0.373588] [PowerGate] name: 'dma', on: 1, after SPS_PG_CTL: 0x703360
[ 0.373694] owl_dma b0260000.dma: actions AHB DMA Controller ( cpy slave memset ), 12 channels
[ 0.375642] atc260x_i2c 0-0065: Probing...
[ 0.375737] atc260x_i2c 0-0065: atc260x_core_dev_init() enter
[ 0.376217] atc260x_i2c 0-0065: set bdg ctl, ret=0 value=0xd1
[ 0.377928] atc260x_i2c 0-0065: detect PMU chip type 1 ver A
[ 0.377954] atc260x_i2c 0-0065: PMU root IRQ 215
[ 0.378583] atc260x_i2c 0-0065: icm_ohm not config, use default value
[ 0.378613] atc260x_i2c 0-0065: auxadc icm_ohm = 20
[ 0.379053] atc260x-regulator atc2603c-dcdc1.1: Probing atc2603c-dcdc1, id=1
[ 0.380245] dcdc1: 700 <--> 1400 mV at 975 mV
[ 0.380768] atc260x-regulator atc2603c-dcdc2.2: Probing atc2603c-dcdc2, id=2
[ 0.382054] dcdc2: 1300 <--> 2150 mV at 1550 mV
[ 0.382542] atc260x-regulator atc2603c-dcdc3.3: Probing atc2603c-dcdc3, id=3
[ 0.383662] dcdc3: 2600 <--> 3300 mV at 3100 mV
[ 0.384162] atc260x-regulator atc2603c-ldo1.1: Probing atc2603c-ldo1, id=1
[ 0.386479] ldo1: 2600 <--> 3300 mV at 3300 mV
[ 0.387014] atc260x-regulator atc2603c-ldo2.2: Probing atc2603c-ldo2, id=2
[ 0.389345] ldo2: 2600 <--> 3300 mV at 3100 mV
[ 0.389848] atc260x-regulator atc2603c-ldo3.3: Probing atc2603c-ldo3, id=3
[ 0.392205] ldo3: 1500 <--> 2000 mV at 1800 mV
[ 0.392706] atc260x-regulator atc2603c-ldo5.5: Probing atc2603c-ldo5, id=5
[ 0.393040] ldo5: 2600 <--> 3300 mV at 2800 mV
[ 0.393537] atc260x-regulator atc2603c-ldo6.6: Probing atc2603c-ldo6, id=6
[ 0.395865] ldo6: 700 <--> 1400 mV at 1100 mV
[ 0.396366] atc260x-regulator atc2603c-ldo7.7: Probing atc2603c-ldo7, id=7
[ 0.399130] ldo7: 1800 mV
[ 0.399642] atc260x-regulator atc2603c-ldo8.8: Probing atc2603c-ldo8, id=8
[ 0.400002] ldo8: 2300 <--> 3300 mV at 3100 mV
[ 0.400559] atc260x-regulator atc2603c-ldo11.11: Probing atc2603c-ldo11, id=11
[ 0.402877] ldo11: 2600 <--> 3300 mV at 3100 mV
[ 0.403393] atc260x-switch-ldo atc2603c-switch1.1: Probing atc2603c-switch1, id=1
[ 0.403448] atc260x-switch-ldo atc2603c-switch1.1: pmic_ver=0
[ 0.403625] [SWITCH1] set switch 1 to ldo mode Version D!
[ 0.404073] switch1: 3000 <--> 3300 mV at 3100 mV
[ 0.404680] atc260x-ext-pwm-dcdc atc2603c-ext-pwm-dcdc1.1: Probing atc2603c-ext-pwm-dcdc1
[ 0.404721] atc260x-ext-pwm-dcdc atc2603c-ext-pwm-dcdc1.1: table_len = 15
[ 0.404908] atc260x-ext-pwm-dcdc atc2603c-ext-pwm-dcdc1.1: got init voltage selector 8
[ 0.405066] vdd-gpu-dcdc: 900 <--> 1250 mV at 1100 mV normal
[ 0.405374] atc260x-ext-pwm-dcdc atc2603c-ext-pwm-dcdc2.2: Probing atc2603c-ext-pwm-dcdc2
[ 0.405414] atc260x-ext-pwm-dcdc atc2603c-ext-pwm-dcdc2.2: table_len = 15
[ 0.405562] atc260x-ext-pwm-dcdc atc2603c-ext-pwm-dcdc2.2: got init voltage selector 6
[ 0.405716] vdd-core-dcdc: 900 <--> 1250 mV at 1050 mV normal
[ 0.406264] atc260x-gpio atc2603c-gpio.0: Probing...
[ 0.406568] atc2603c-sgpio atc2603c-sgpio.0: Probing...
[ 0.406999] atc2603c-sgpio atc2603c-sgpio.0: new IRQ mapping: hwirq0 -> virq219
[ 0.407040] atc2603c-sgpio atc2603c-sgpio.0: new IRQ mapping: hwirq1 -> virq220
[ 0.407075] atc2603c-sgpio atc2603c-sgpio.0: new IRQ mapping: hwirq2 -> virq221
[ 0.407109] atc2603c-sgpio atc2603c-sgpio.0: new IRQ mapping: hwirq3 -> virq222
[ 0.407142] atc2603c-sgpio atc2603c-sgpio.0: new IRQ mapping: hwirq4 -> virq223
[ 0.407175] atc2603c-sgpio atc2603c-sgpio.0: new IRQ mapping: hwirq5 -> virq224
[ 0.407208] atc2603c-sgpio atc2603c-sgpio.0: new IRQ mapping: hwirq6 -> virq225
[ 0.407236] atc2603c-sgpio atc2603c-sgpio.0: root virq num : 218
[ 0.408863] atc260x_i2c 0-0065: atc260x_core_dev_init() exit
[ 0.409299] atc260x-pm atc2603c-pm.0: Probing...
[ 0.409618] atc260x-pm atc2603c-pm.0: _set_s2_mode() can not get of_property s2_mode
[ 0.409657] atc260x-pm atc2603c-pm.0: _atc260x_pm_set_wakeup_src_inner() enter, mask=0x7fff src=0x706
[ 0.409996] atc260x-pm atc2603c-pm.0: _atc260x_pm_set_wakeup_src_inner() setup reg=0x0 msk=0xffe0 val=0xe0c0 readback=0xe0cb
[ 0.410331] atc260x-pm atc2603c-pm.0: _atc260x_pm_set_wakeup_src_inner() setup reg=0x3 msk=0xc val=0x0 readback=0x4080
[ 0.410663] atc260x-pm atc2603c-pm.0: _atc260x_pm_set_wakeup_src_inner() enter, mask=0x8 src=0x0
[ 0.410990] atc260x-pm atc2603c-pm.0: _atc260x_pm_set_wakeup_src_inner() setup reg=0x0 msk=0x100 val=0x0 readback=0xe0cb
[ 0.411750] atc260x-pm atc2603c-pm.0: _clear_status() no need to restore old alarm
[ 0.412919] atc260x-pm atc2603c-pm.0: got support_adaptor_type: 3
[ 0.413525] atc260x-pm atc2603c-pm.0: translated wakeup falgs: 0x200
[ 0.413637] [PM] set pmic suspend ops 0xc0ae4d48
[ 0.413815] atc260x-pm atc2603c-pm.0: #####atc260x_pm_probe PMU_SYS_CTL0:0xe0cb ####
[ 0.414206] SCSI subsystem initialized
[ 0.414307] ASOC SPI: enter spi probe
[ 0.414660] asoc_spi0 b0208000.spi: master is unqueued, this is deprecated
[ 0.414993] ahb freq is 100000000
[ 0.415560] usbcore: registered new interface driver usbfs
[ 0.415652] usbcore: registered new interface driver hub
[ 0.415819] usbcore: registered new device driver usb
[ 0.415982] Linux video capture interface: v2.00
[ 0.419236] owl_ion_probe: add heap ion_fb
[ 0.419279] owl_ion_probe: add heap ion_pmem
[ 0.419414] owl_ion_probe: add heap ion_system
[ 0.419624] Advanced Linux Sound Architecture Driver Initialized.
[ 0.420321] Bluetooth: Core ver 2.16
[ 0.420396] NET: Registered protocol family 31
[ 0.420418] Bluetooth: HCI device and connection manager initialized
[ 0.420458] Bluetooth: HCI socket layer initialized
[ 0.420486] Bluetooth: L2CAP socket layer initialized
[ 0.420537] Bluetooth: SCO socket layer initialized
[ 0.420972] cfg80211: Calling CRDA to update world regulatory domain
[ 0.422306] Switching to clocksource timer0
[ 0.470462] NET: Registered protocol family 2
[ 0.471223] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.471419] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.471595] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.471684] TCP: reno registered
[ 0.471714] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 0.471777] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 0.472146] NET: Registered protocol family 1
[ 0.472697] RPC: Registered named UNIX socket transport module.
[ 0.472729] RPC: Registered udp transport module.
[ 0.472749] RPC: Registered tcp transport module.
[ 0.472769] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.473054] Trying to unpack rootfs image as initramfs...
[ 1.644508] Freeing initrd memory: 14392K (c2000000 - c2e0e000)
[ 1.645005] hw perfevents: enabled with ARMv7_Cortex_A9 PMU driver, 7 counters available
[ 1.645578] owl_uart: no device is found
[ 1.645800] b0124000.serial: ttyS2 at MMIO 0xb0124000 (irq = 63) is a OWL_SERIAL
[ 2.835553] console [ttyS2] enabled
[ 2.839614] ## boot_dev: 0x20
[ 2.843312] audit: initializing netlink socket (disabled)
[ 2.848747] type=2000 audit(2.830:1): initialized
[ 2.867018] NTFS driver 2.1.30 [Flags: R/W].
[ 2.871952] fuse init (API version 7.22)
[ 2.876508] exFAT: Core Version 1.1.3
[ 2.880169] exFAT: FS Version 1.1.3
[ 2.883892] msgmni has been set to 1434
[ 2.887768] SELinux: Registering netfilter hooks
[ 2.890499] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 2.897932] io scheduler noop registered
[ 2.901851] io scheduler deadline registered
[ 2.906330] io scheduler cfq registered (default)
[ 2.914946] #### insmod vde driver!
[ 2.918763] mali0 b0280000.vde: Probe vde device
[ 2.923406] info ic_type 0x5206
[ 2.926636] vde->irq =52
[ 2.929228] cputherm_register_notifier list 0
[ 2.936739] mali0 b0280000.vde: resource: iomem: [mem 0xb0280000-0xb0280107] mapping to f8280000, irq 82
[ 2.946241] sps base = 0xf81b0100
[ 2.949548] cmu base = 0xf8160000
[ 2.952868] SPS_PG_CTL = 0xf81b0100
[ 2.956347] Share_Mem_REG = 0xf8240004
[ 2.960086] CMU_COREPLL = 0xf8160000
[ 2.963665] CMU_VDE_CLK = 0xf8160040
[ 2.967230] CMU_DEVRST0 = 0xf81600a8
[ 2.970794] CMU_DEVCLKEN0 = 0xf81600a0
[ 2.974715] device_create_file !
[ 2.978678] owl_dss DE: owl_de_probe, pdev = 0xe22f5200
[ 2.983941] owl_dss DE: DE INITED FROM UBOOT ?? 1
[ 2.988750] owl_dss DE: de irq init ok
[ 3.005198] owl_dss MMU: mmu_init: base 0xe3a00000 base_phys 0xc0a51d6823a00000 free_info->addr 0xe3a00000
[ 3.015943] 1 portname = dsi
[ 3.018909] generic_dsi_panel_drv_init
[ 3.022958] owl_dsihw_probe
[ 3.025777] owl_dss DSI: error!dsihw_parse_params, fail to get lcd reset gpio
[ 3.033005] owl_dss DSI: owl_dsihw_probe called ok ~~~~~~~~~~~~~
[ 3.039393] 1 portname = dsi
[ 3.042353] current type dsi
[ 3.045397] dss_recheck_connections dssdev->type 2
[ 3.050445] OWL_HDMI: Enter owldss_hdmihw_probe
[ 3.055008] OWL_HDMI_DEBUG: hdmi info ic_type 0x3
[ 3.055017] OWL_HDMI_DEBUG: of_get_hdmi_data
[ 3.055032] OWL_HDMI_ERR: cat not get vid480p_tx1
[ 3.059824] OWL_HDMI_DEBUG: base=f82c0000
[ 3.059832] OWL_HDMI_DEBUG: init_display
[ 3.060676] dss_recheck_connections dssdev->type 32
[ 3.065666] OWL_HDMI_DEBUG: ENTER hdmi_panel_probe
[ 3.065678] OWL_HDMI_DEBUG: hdmi_panel_probe x_res= 0 y_res = 0
[ 3.065687] OWL_HDMI_DEBUG: owl_dss_device hdmi p->0xc0addb70
[ 3.065693] OWL_HDMI_DEBUG: hpd_enable start
[ 3.065724] OWL_HDMI: register irq ON!
[ 3.079414] brd: module loaded
[ 3.087570] loop: module loaded
[ 3.090720] misc_info_init, line 1059, Nov 21 2015 10:33:06
[ 3.096477] mi_debug_init, line 372
[ 3.100363] atc260x-pwm atc2603c-pwm.0: atc260x_pwm Probing...
[ 3.106334] no blk dev
[ 3.108692] read MiscInfoHeader failed
[ 3.112465] read Head failed
[ 3.112502] atc260x_pwm_drv: [atc260x_pwm_on start]
[ 3.120236] OWL_HDMI_ERR: failed to read hdcp key from secure storage
[ 3.127130] atc260x_pwm_drv: [atc260x_pwm_on finished]
[ 3.132594] tun: Universal TUN/TAP device driver, 1.6
[ 3.137642] tun: (C) 1999-2004 Max Krasnyansky
[ 3.144069] PPP generic driver version 2.4.2
[ 3.148541] PPP BSD Compression module registered
[ 3.153271] PPP Deflate Compression module registered
[ 3.158331] PPP MPPE Compression module registered
[ 3.163136] NET: Registered protocol family 24
[ 3.167709] usbcore: registered new interface driver rtl8150
[ 3.173442] usbcore: registered new interface driver r8152
[ 3.178970] usbcore: registered new interface driver ax88179_178a
[ 3.185127] usbcore: registered new interface driver cdc_ether
[ 3.191013] usbcore: registered new interface driver cdc_subset
[ 3.197039] usbcore: registered new interface driver cdc_ncm
[ 3.202778] usbcore: registered new interface driver asix
[ 3.208220] usbcore: registered new interface driver sr9700_android
[ 3.214560] usbcore: registered new interface driver CoreChips
[ 3.220716]
------------dwc3_clk_init-----ic=1-----
[ 3.229558] [PowerGate] name: 'usb3', on: 1, before SPS_PG_CTL: 0x703360
[ 3.236348] [PowerGate] name: 'usb3', on: 1, after SPS_PG_CTL: 0x707760
[ 3.244141] GS705A phy init for dwc3 gadget 10:33:34
[ 3.249409] GS705A phy init for dwc3 gadget 10:33:34
[ 3.269199] aotg_hcd b0600000.usb: can't find usbh-1 dts node
[ 3.274990] aotg_hcd b0600000.usb: aotg_hub_probe: usb probe hcd failed, error is -19
[ 3.283086] aotg_hcd b0700000.usb: can't find usbh-1 dts node
[ 3.288833] aotg_hcd b0700000.usb: aotg_hub_probe: usb probe hcd failed, error is -19
[ 3.297029] port_host_plug_detect[0]:1
[ 3.300804] port0_vubs_en:36
[ 3.303769] port_host_plug_detect[1]:1
[ 3.307519] fail to request vbus gpio [36]
[ 3.311609] port1_vubs_en:36
[ 3.314696] [PowerGate] name: 'usb2_0', on: 1, before SPS_PG_CTL: 0x707760
[ 3.321637] [PowerGate] name: 'usb2_0', on: 1, after SPS_PG_CTL: 0x70ff60
[ 3.328441] start mon 0 ......
[ 3.331634] [PowerGate] name: 'usb2_1', on: 1, before SPS_PG_CTL: 0x70ff60
[ 3.338591] [PowerGate] name: 'usb2_1', on: 1, after SPS_PG_CTL: 0x74ff64
[ 3.345390] start mon 1 ......
[ 3.348564] usbcore: registered new interface driver cdc_acm
[ 3.354242] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 3.362317] usbcore: registered new interface driver usb-storage
[ 3.368465] usbcore: registered new interface driver usbserial
[ 3.374360] usbcore: registered new interface driver option
[ 3.379966] usbserial: USB Serial support registered for GSM modem (1-port)
[ 3.387557] mousedev: PS/2 mouse device common for all mice
[ 3.393566] atc260x-onoff atc2603c-onoff.0: Probing atc2603c-onoff
[ 3.399752] atc260x-onoff atc2603c-onoff.0: atc260x_onoff IRQ num : 216
[ 3.406637] input: atc260x_onoff as /devices/b0170000.i2c/i2c-0/0-0065/atc2603c-onoff.0/input/input0
[ 3.416862] usbcore: registered new interface driver usb_acecad
[ 3.422873] usbcore: registered new interface driver aiptek
[ 3.428488] usbcore: registered new interface driver gtco
[ 3.433952] usbcore: registered new interface driver hanwang
[ 3.439651] usbcore: registered new interface driver kbtab
[ 3.445196] usbcore: registered new interface driver wacom
[ 3.451177] atc260x-rtc atc2603c-rtc.0: Probing...
[ 3.459553] atc260x-rtc atc2603c-rtc.0: rtc core: registered atc260x-RTC as rtc0
[ 3.467292] atc260x-rtc atc2603c-rtc.0: invalid year(0), reset to year 2011
[ 3.475354] atc260x-rtc atc2603c-rtc.0: RTC alarm IRQ num : 217
[ 3.482073] atc260x-hwmon atc2603c-hwmon.0: Probing atc2603c-hwmon
[ 3.488668] tmu-mem:start=0xb01b00e8
[ 3.492859] device-mapper: uevent: version 1.0.3
[ 3.497927] device-mapper: ioctl: 4.24.0-ioctl (2013-01-15) initialised: dm-devel@redhat.com
[ 3.506759] Bluetooth: HCI UART driver ver 2.2
[ 3.511202] Bluetooth: HCI H4 protocol initialized
[ 3.516009] Bluetooth: HCI Three-wire UART (H5) protocol initialized
[ 3.522355] rtk_btusb: Realtek Bluetooth USB driver module init, version 2.21
[ 3.529587] usbcore: registered new interface driver rtk_btusb
[ 3.535562] cpuidle: using governor ladder
[ 3.539656] cpuidle: using governor menu
[ 3.544113] ## host_id: 0 boot_dev 20 host->index: 0
[ 3.549763] gl520x_mmc b0230000.mmc: using dma0chan0 for DMA transfers
[ 3.556344] use GPIO to detect SD/MMC card
[ 3.560470] owl pinctrl: 1gpio_request_check_pinmux
[ 3.565451] owl pinctrl: 1CHECK PMX:P_UART2_CTSB has already been requested by b0124000.serialhost0: sure rescan mmc
[ 3.576452] hidraw: raw HID events driver (C) Jiri Kosina
[ 3.584983] usbcore: registered new interface driver usbhid
[ 3.590557] usbhid: USB HID core driver
[ 3.595125] zram: Created 1 device(s) ...
[ 3.599780] ashmem: initialized
[ 3.603206] logger: created 256K log 'log_main'
[ 3.607949] logger: created 256K log 'log_events'
[ 3.612892] logger: created 256K log 'log_radio'
[ 3.617735] logger: created 256K log 'log_system'
[ 3.623618] [SNDRV]:[atm7059_pcm_init] atm7059_pcm_init!!
[ 3.623841] atm7059-pcm-audio atm7059-pcm-audio: atm7059_pcm_probe!!
[ 3.630237] atc2603a_init
[ 3.633070] [SNDRV]:[atc2603a_get_cfg] Fail to get device_node
[ 3.640467] [SNDRV]:[atc2603a_init] audio get cfg failed!
[ 3.647444] atc2603c_init
[ 3.650094] fail get earphone_detect_method
[ 3.654372] fail get adc level
[ 3.657791] [SNDRV]:[atc2603c_platform_probe] atc2603c_platform_probe
[ 3.666135] [SNDRV]:[atm7059_dai_probe] it's ok 0
[ 3.672334] owl-audio-i2s b0100000.gl5203-audio-i2s: atm7059_dai_probe
[ 3.679434] atm7059-hdmi-audio atm7059-hdmi-audio: atm7059_hdmi_probe!!
[ 3.686123] [SNDRV]:[atm7059_link_init] atm7059_link_init
[ 3.693182] [SNDRV]:[atm7059_audio_gpio_init] GPIO[126] request failed
[ 3.701699] soc-audio soc-audio: ASoC: machine atm7059_link should use snd_soc_register_card()
[ 3.710558] [SNDRV]:[atc2603c_probe] atc2603c_probe!
[ 3.710574] [SNDRV]:[atc2603c_probe] codec->name = atc260x-audio
[ 3.771143] acts_mmc_get_ro: Card read-only status -38
[ 3.776305] mmc0: host does not support reading read-only switch. assuming write-enable.
[ 3.785270] sd card init ok
[ 3.788062] mmc_add_card: bootdev 0x20
[ 3.791801] force sd0/sd1 host ext-card
[ 3.795657] mmc0: new ultra high speed SDR50 SDHC card at address 1234
[ 3.802440] ## md->name_idx: 0
[ 3.805786] mmcblk0: sd_card SA16G 14.6 GiB
[ 3.817657] GPT:Primary header thinks Alt. header is not at the end of the disk.
[ 3.825138] GPT:14680063 != 30703615
[ 3.828707] GPT:Alternate GPT header not at the end of the disk.
[ 3.834727] GPT:14680063 != 30703615
[ 3.838293] GPT: Use GNU Parted to correct GPT errors.
[ 3.843470] mmcblk0: p1 p2 p3
[ 3.856114] atc2603c-audio atc260x-audio: ASoC: no dapm match for AOUT FL FR Mixer --> AOUT MIXER --> ADC0 Mux
[ 3.866152] atc2603c-audio atc260x-audio: ASoC: Failed to add route AOUT FL FR Mixer -> AOUT MIXER -> ADC0 Mux
[ 3.876781] [SNDRV]:[codec_hdmi_probe] codec_hdmi_probe!
[ 3.878231] [SNDRV]:[atm7059_link_snd_init] atm7059_link_init() called
[ 3.879421] soc-audio soc-audio: atc2603c-dai <-> owl-audio-i2s mapping ok
[ 3.886563] [SNDRV]:[atm7059_link_snd_init] atm7059_link_init() called
[ 3.887067] soc-audio soc-audio: atm7059-hdmi-dai <-> owl-audio-i2s mapping ok
[ 3.895967] u32 classifier
[ 3.898677] Actions configured
[ 3.902074] Netfilter messages via NETLINK v0.30.
[ 3.906877] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[ 3.913710] ctnetlink v0.93: registering with nfnetlink.
[ 3.919127] NF_TPROXY: Transparent proxy support initialized, version 4.1.0
[ 3.926119] NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd.
[ 3.932501] xt_time: kernel timezone is -0000
[ 3.937259] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 3.942854] ipt_CLUSTERIP: ClusterIP Version 0.8 loaded successfully
[ 3.949274] arp_tables: (C) 2002 David S. Miller
[ 3.953978] TCP: cubic registered
[ 3.957288] Initializing XFRM netlink socket
[ 3.962298] NET: Registered protocol family 10
[ 3.967593] mip6: Mobile IPv6
[ 3.970608] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 3.976251] sit: IPv6 over IPv4 tunneling driver
[ 3.982214] NET: Registered protocol family 17
[ 3.986774] NET: Registered protocol family 15
[ 3.991219] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 3.997167] Bluetooth: HIDP socket layer initialized
[ 4.002178] l2tp_core: L2TP core driver, V2.0
[ 4.006572] l2tp_ppp: PPPoL2TP kernel driver, V2.0
[ 4.011356] lib80211: common routines for IEEE802.11 drivers
[ 4.017038] lib80211_crypt: registered algorithm 'NULL'
[ 4.017049] lib80211_crypt: registered algorithm 'WEP'
[ 4.017057] lib80211_crypt: registered algorithm 'CCMP'
[ 4.017065] lib80211_crypt: registered algorithm 'TKIP'
[ 4.017358] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[ 4.025065] ThumbEE CPU extension supported.
[ 4.029465] [PM] owl_pm_init() 1006
[ 4.032978] train_Msize:2048, train_ces:2
[ 4.054551] start:0xc0008000, end:0xc0a286e0, checksum:0xc8ad4b3b
[ 4.061831] owlfb owlfb: no driver for display: lcd
[ 4.066768] owlfb owlfb: no driver for display: edp
[ 4.123108] Console: switching to colour frame buffer device 160x50
[ 4.202473] store_mirror_to_hdmi 1
[ 4.205991] OWL_HDMI_DEBUG: hdmi_get_vid
[ 4.206002] OWL_HDMI_DEBUG: hdmi_set_vid
[ 4.206012] OWL_HDMI: ~~~~~~~~~~~~owldss_hdmi_display_set_vid 16
[ 4.212210] OWL_HDMI_DEBUG: ENTER hdmi_panel_enable
[ 4.212217] OWL_HDMI: ENTER hdmi_display_enable
[ 4.216930] OWL_HDMI_DEBUG: owl_dss_start_device end
[ 4.217033] store_mirror_to_hdmi 1
[ 4.220546] OWL_HDMI_DEBUG: hdmi_get_vid
[ 4.220555] OWL_HDMI_DEBUG: hdmi_set_vid
[ 4.220565] OWL_HDMI: ~~~~~~~~~~~~owldss_hdmi_display_set_vid 16
[ 4.226784] OWL_HDMI_DEBUG: ENTER hdmi_panel_enable
[ 4.226848] store_mirror_to_hdmi 1
[ 4.230358] OWL_HDMI_DEBUG: hdmi_get_vid
[ 4.230366] OWL_HDMI_DEBUG: hdmi_set_vid
[ 4.230375] OWL_HDMI: ~~~~~~~~~~~~owldss_hdmi_display_set_vid 16
[ 4.236590] OWL_HDMI_DEBUG: ENTER hdmi_panel_enable
[ 4.236653] store_mirror_to_hdmi 1
[ 4.240162] OWL_HDMI_DEBUG: hdmi_get_vid
[ 4.240172] OWL_HDMI_DEBUG: hdmi_set_vid
[ 4.240180] OWL_HDMI: ~~~~~~~~~~~~owldss_hdmi_display_set_vid 16
[ 4.246395] OWL_HDMI_DEBUG: ENTER hdmi_panel_enable
[ 4.246458] store_mirror_to_hdmi 1
[ 4.249968] OWL_HDMI_DEBUG: hdmi_get_vid
[ 4.249977] OWL_HDMI_DEBUG: hdmi_set_vid
[ 4.249985] OWL_HDMI: ~~~~~~~~~~~~owldss_hdmi_display_set_vid 16
[ 4.256199] OWL_HDMI_DEBUG: ENTER hdmi_panel_enable
[ 4.256262] store_mirror_to_hdmi 1
[ 4.265794] OWL_HDMI_DEBUG: hdmi_get_vid
[ 4.265804] OWL_HDMI_DEBUG: hdmi_set_vid
[ 4.265814] OWL_HDMI: ~~~~~~~~~~~~owldss_hdmi_display_set_vid 16
[ 4.278017] OWL_HDMI_DEBUG: ENTER hdmi_panel_enable
[ 4.278084] store_mirror_to_hdmi 1
[ 4.287577] OWL_HDMI_DEBUG: hdmi_get_vid
[ 4.287588] OWL_HDMI_DEBUG: hdmi_set_vid
[ 4.287596] OWL_HDMI: ~~~~~~~~~~~~owldss_hdmi_display_set_vid 16
[ 4.299816] OWL_HDMI_DEBUG: ENTER hdmi_panel_enable
[ 4.300204] np c1c7cad8
[ 4.308838] boot_hdmi_rotate 3
[ 4.318020] boot_hdmi_rotate 3
[ 4.327438] regulator-dummy: disabling
[ 4.337865] atc260x-rtc atc2603c-rtc.0: setting system clock to 2011-01-01 00:00:21 UTC (1293840021)
[ 4.354870] ATC260X_POWER: create sysfs for atc260x power
[ 4.442858] charger=e1e2d0c8 2691
[ 4.452311] set_vbus_path=c0472f1c set_apds_vbus_pd=c0472ff0
[ 4.466807] ====otgvbus_gpio: num-37, active-high---detect_type=3,idpin_type=0,vbus_type=2---
[ 4.478884] owl pinctrl: 1gpio_request_check_pinmux
[ 4.487384] ++++++++cpufreq ready++++++++
[ 4.494892] ++++++++pdata->freq_tab[0].freq_clip_max:504000++++++++
[ 4.504778] ++++++++pdata->freq_tab[1].freq_clip_max:504000++++++++
[ 4.519839] OWL: Kernel Thermal management registered
[ 4.520920] owl pinctrl: 1CHECK PMX:P_KS_IN2 has already been requested by gl5206-pwm0
[ 4.520921] ALSA device list:
[ 4.520925] #0: atm7059_link
[ 4.553587] Freeing unused kernel memory: 448K (c0a29000 - c0a99000)
[ 4.589072] mmc0: Slot status change detected (0 -> 1)
[ 4.638356] systemd-udevd[123]: starting version 215
[ 4.862820]
[power] No battery detected
[ 4.934281] ATC260X_POWER: atc260x_charger_adjust_current:set constant current:400mA(binary:3)
[ 4.946884] [atc260x_usb_get_prop] first_power_on = false!
[ 4.992996]
========usb_detect_plugout_event===start det!!========
[ 5.008432]
----udc_set_plugstate--PLUGSTATE_OUT--
[ 5.022610]
------------dwc3_clk_exit----------
[ 5.167044] read_mi_head, line 429, magic 0x0, length 0, item num 0
[ 5.177188] read Head null
[ 5.183667] OWL_HDMI_ERR: failed to read hdcp key from secure storage
[ 5.672416]
----udc_set_plugstate--PLUGSTATE_IN-2--
[ 5.686581]
------------dwc3_clk_init-----ic=1-----
[ 5.702534] [PowerGate] 'usb3', skip power on, count 2
[ 5.878055] GS705A phy init for dwc3 gadget 10:33:34
[ 5.886984] GS705A phy init for dwc3 gadget 10:33:34
[ 5.895987] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 5.905444] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[ 5.917154] GS705A phy init for xhci 10:33:34
[ 5.926396] xhci-hcd xhci-hcd.0.auto: irq 55, io mem 0xb0400000
[ 5.936140] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 5.946676] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 5.957685] usb usb1: Product: xHCI Host Controller
[ 5.966311] usb usb1: Manufacturer: Linux 3.10.37 xhci-hcd
[ 5.975510] usb usb1: SerialNumber: xhci-hcd.0.auto
[ 5.984492] xHCI xhci_add_endpoint called for root hub
[ 5.984502] xHCI xhci_check_bandwidth called for root hub
[ 5.984659] hub 1-0:1.0: USB hub found
[ 5.992103] hub 1-0:1.0: 1 port detected
[ 6.000002] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 6.009455] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[ 6.020831]
#xhci_start#
[ 6.044885] ss_try_next_mode:lfps_src_mode=1
[ 6.058339] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003
[ 6.068698] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 6.079494] usb usb2: Product: xHCI Host Controller
[ 6.087921] usb usb2: Manufacturer: Linux 3.10.37 xhci-hcd
[ 6.096997] usb usb2: SerialNumber: xhci-hcd.0.auto
[ 6.105800] xHCI xhci_add_endpoint called for root hub
[ 6.105810] xHCI xhci_check_bandwidth called for root hub
[ 6.105952] hub 2-0:1.0: USB hub found
[ 6.113243] hub 2-0:1.0: 1 port detected
[ 6.120880] ----monitor_wake_lock for 10s
[ 10.380636] EXT4-fs (mmcblk0p3): mounted filesystem with ordered data mode. Opts: (null)
[ 10.681771] systemd[1]: systemd 215 running in system mode. (+PAM +AUDIT +SELINUX +IMA +SYSVINIT +LIBCRYPTSETUP +GCRYPT +ACL +XZ -SECCOMP -APPARMOR)
[ 10.699056] systemd[1]: Detected architecture 'arm'.
[ 10.738228] systemd[1]: Set hostname to .
[ 10.747979] systemd[1]: Initializing machine ID from random generator.
[ 10.758231] systemd[1]: Installed transient /etc/machine-id file.
[ 10.828277] open ttyS2
[ 11.065922] systemd[1]: Starting Forward Password Requests to Wall Directory Watch.
[ 11.069969] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[ 11.073783] systemd[1]: Expecting device dev-ttyS2.device...
[ 11.081623] systemd[1]: Starting Remote File Systems (Pre).
[ 11.089503] systemd[1]: Reached target Remote File Systems (Pre).
[ 11.093389] systemd[1]: Starting Encrypted Volumes.
[ 11.101139] systemd[1]: Reached target Encrypted Volumes.
[ 11.105039] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[ 11.108990] systemd[1]: Starting Dispatch Password Requests to Console Directory Watch.
[ 11.113220] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
[ 11.117234] systemd[1]: Starting Paths.
[ 11.125281] systemd[1]: Reached target Paths.
[ 11.129242] systemd[1]: Starting Swap.
[ 11.137140] systemd[1]: Reached target Swap.
[ 11.141064] systemd[1]: Starting Root Slice.
[ 11.149082] systemd[1]: Created slice Root Slice.
[ 11.153022] systemd[1]: Starting User and Session Slice.
[ 11.161073] systemd[1]: Created slice User and Session Slice.
[ 11.165048] systemd[1]: Starting /dev/initctl Compatibility Named Pipe.
[ 11.173382] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
[ 11.177501] systemd[1]: Starting Delayed Shutdown Socket.
[ 11.185749] systemd[1]: Listening on Delayed Shutdown Socket.
[ 11.189782] systemd[1]: Starting Journal Socket (/dev/log).
[ 11.198052] systemd[1]: Listening on Journal Socket (/dev/log).
[ 11.201931] systemd[1]: Starting udev Control Socket.
[ 11.209883] systemd[1]: Listening on udev Control Socket.
[ 11.213805] systemd[1]: Starting udev Kernel Socket.
[ 11.221634] systemd[1]: Listening on udev Kernel Socket.
[ 11.225539] systemd[1]: Starting Journal Socket.
[ 11.233476] systemd[1]: Listening on Journal Socket.
[ 11.237318] systemd[1]: Starting System Slice.
[ 11.245132] systemd[1]: Created slice System Slice.
[ 11.248891] systemd[1]: Starting File System Check on Root Device...
[ 11.258413] systemd[1]: Starting system-getty.slice.
[ 11.266879] systemd[1]: Created slice system-getty.slice.
[ 11.270900] systemd[1]: Starting system-serial\x2dgetty.slice.
[ 11.279121] systemd[1]: Created slice system-serial\x2dgetty.slice.
[ 11.283071] systemd[1]: Starting Increase datagram queue length...
[ 11.292884] systemd[1]: Mounted POSIX Message Queue File System.
[ 11.297278] systemd[1]: Starting udev Coldplug all Devices...
[ 11.307640] systemd[1]: Started live-config contains the components that configure a live system during the boot process (late userspace)..
[ 11.331340] systemd[1]: Starting Load Kernel Modules...
[ 11.348732] systemd[1]: Started Set Up Additional Binary Formats.
[ 11.353113] systemd[1]: Mounted Huge Pages File System.
[ 11.373308] systemd[1]: Starting Create list of required static device nodes for the current kernel...
[ 11.385639] systemd[1]: Mounting Debug File System...
[ 11.397422] systemd[1]: Starting Slices.
[ 11.406600] systemd[1]: Reached target Slices.
[ 11.418571] systemd[1]: Mounted Debug File System.
[ 11.428024] systemd[1]: Started Increase datagram queue length.
[ 11.441180] systemd[1]: Started Create list of required static device nodes for the current kernel.
[ 11.449753] asoc_ethernet_init 3729
[ 11.455453] read_mi_head, line 429, magic 0x0, length 0, item num 0
[ 11.459933] read Head null
[ 11.464437] random-mac-address: disabled
[ 11.468837] no local-mac-address in dts
[ 11.473628] use the mac address by chip
[ 11.473638] print_mac_address f4-
[ 11.473643] print_mac_address 4e-
[ 11.473647] print_mac_address fd-
[ 11.473650] print_mac_address fb-
[ 11.473654] print_mac_address f1-
[ 11.473657] print_mac_address 7e
[ 11.473675] phy_mode_str: rmii
[ 11.473709] phy_mode: 0
[ 11.478183] target freq: 50000000
[ 11.482560] pdev->name: b0310000.ethernet
[ 11.482603] phy_mode: 0
[ 11.482652] asoc_ethernet_probe can't get phy power gpio
[ 11.487260] gpio phy-reset-gpios num 88 active 0
[ 11.487652] ethernet phy name: rtl8201
[ 11.487930] ethernet phy's compatible: realtk,rtl8201
[ 11.487944] compatible of /ethernet@b0310000/ethernet-phy@0: realtk,rtl8201
[ 11.492817] phy_model: 3
[ 11.492823] res->start: b0310000, ecp->hwrp: f8310000
[ 11.492826] phy model: RTL8201
[ 11.492838] ETHERNET_BASE: 0xb0310000
[ 11.492840] ecp->hwrp: 0xf8310000
[ 11.497689] ecp->tx_bd_base:e49ea000, ecp->tx_bd_paddr:249ea000
[ 11.497694] ecp->rx_bd_base:e49eb000, ecp->rx_bd_paddr:249eb000
[ 11.497696] virt_to_phys(ecp->tx_bd_base):249ea000
[ 11.498800] 6net device : eth0 init over.
[ 11.498801] ethernet eth0 probe finish
[ 11.515185] systemd[1]: Started udev Coldplug all Devices.
[ 11.525101] systemd[1]: Started Load Kernel Modules.
[ 11.544031] systemd[1]: Starting Apply Kernel Variables...
[ 11.555757] systemd[1]: Mounting Configuration File System...
[ 11.566424] systemd[1]: Mounting FUSE Control File System...
[ 11.579096] systemd[1]: Starting Create Static Device Nodes in /dev...
[ 11.591668] systemd[1]: Starting Syslog Socket.
[ 11.600286] systemd[1]: Listening on Syslog Socket.
[ 11.604799] systemd[1]: Starting Journal Service...
[ 11.619506] systemd[1]: Started Journal Service.
[ 11.917681] systemd-udevd[215]: starting version 215
[ 12.718483] [atc260x_irkeypad_probe start]
[ 12.722629] atc260x-irkeypad atc2603c-irkeypad.0: size = 28
[ 12.726418] atc260x_irkeypad: ir_ch = 1
[ 12.730433] atc260x-irkeypad atc2603c-irkeypad.0: user_code = 16448
[ 12.735429] atc260x-irkeypad atc2603c-irkeypad.0: protocol = 1
[ 12.739226] atc260x-irkeypad atc2603c-irkeypad.0: wk_code = 77
[ 12.743912] atc260x-irkeypad atc2603c-irkeypad.0: period = 140
[ 12.747766] gl5201_irkeypad_drv: [atc260x_irkeypad_probe] get irq: 226
[ 12.762906] input: atc2603c-irkeypad as /devices/b0170000.i2c/i2c-0/0-0065/atc2603c-irkeypad.0/input/input1
[ 12.767496] gl5201_irkeypad_drv: [asoc_irkeypad_open start]
[ 12.771269] gl5201_irkeypad_drv: [asoc_irkeypad_start start]
[ 12.775900] gl5201_irkeypad_drv: [asoc_irkeypad_config start]
[ 12.783315] gl5201_irkeypad_drv: [asoc_irkeypad_config finished]
[ 12.787363] gl5201_irkeypad_drv: [asoc_irkeypad_start finished]
[ 12.792241] gl5201_irkeypad_drv: [asoc_irkeypad_open finished]
[ 12.802538] [atc260x_irkeypad_probe finished]
[ 12.808007] asoc_ethernet_init():3732: 6asoc_ethernet_init 3732
[ 12.811630] Error: Driver 'owl-ethernet' is already registered, aborting...
[ 12.903369] [drm] Initialized drm 1.1.0 20060810
[ 13.120130] mode: [0-->2] !
[ 13.123678] cputherm_register_notifier list 0
[ 13.127112] GPU Init success!
[ 13.130463] In normal mode 2
[ 13.134084] [drm] Initialized pvrsrvkm 1.14.3625561 20110701 on minor 0
[ 18.939484] EXT4-fs (mmcblk0p3): re-mounted. Opts: errors=remount-ro
[ 19.105750] systemd-journald[211]: Received request to flush runtime journal from PID 1
[ 20.332545] atc260x-rtc atc2603c-rtc.0: atc260x_rtc_settime(): 2011-01-01 00:00:37
[ 20.821131] phy_reg_set_bits 339 write reg_val:0xffff
[ 20.821813] phy_reg_set_bits 342 write after read reg_val:0xffff
[ 20.828904] MII_ADVERTISE: 0x01e1
[ 20.829249] phy_init 442 MII_BMCR: 0x1000
[ 20.829591] phy_reg_set_bits 339 write reg_val:0x1200
[ 20.830266] phy_reg_set_bits 342 write after read reg_val:0x1000
[ 20.830270] start aneg...
[ 20.830609] phy_init 447 MII_BMCR: 0x1000
[ 20.830613] link status is: false
[ 20.833939] eth0 link off.
[ 20.837281] INTC_EXTCTL: 0x00000020
[ 20.837292] PAD_PULLCTL0: 0x00004be2
[ 20.837297] INTC_EXTCTL: 0x00600020
[ 20.837353] IRQ 32 requested
[ 20.840265] ec_netdev_set_multicast_list 2694
[ 20.840291] ec_netdev_set_multicast_list 2694
[ 20.840664] ec_netdev_set_multicast_list 2694
[ 20.840707] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 21.000322] open ttyS2
[ 21.003902] open ttyS2
[ 21.041839] open ttyS2
[ 21.045100] open ttyS2
[ 23.833474] exit
[ 21.020238] owlfb_blank~~~~~~~~~~~~~~~blank 1owlfb_blank~~~~~~~~~~~~~~~blank 0
[ 23.833833] ecp->autoneg:1
[ 23.834685]
autoneg -> speed:100, duplex:full, pause: non-supported
[ 23.840665] set_mac_according_aneg
[ 23.840839] opmode regs old value - 0x2202
[ 23.841180] old MII_BMCR: 0x3100
[ 23.841855] new MII_BMCR: 0x3100
[ 23.841859] hw_regs->er_opmode:0x2202
[ 23.842197] link established.
[ 23.845220] ethernet link state:linked
[ 23.849859] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 23.856377] ec_netdev_set_multicast_list 2694
[ 23.857748] read phy reg-4
[ 23.858102] read phy reg-0
[ 23.858444] read phy reg-5
[ 23.866564] ec_netdev_set_multicast_list 2694
[ 24.681758] ec_netdev_set_multicast_list 2694
[ 26.033085] ec_netdev_set_multicast_list 2694
[ 26.342991] ec_netdev_set_multicast_list 2694
[ 139.120117] ec_netdev_set_multicast_list 2694
[ 139.120273] ec_netdev_set_multicast_list 2694
[ 139.120306] ec_netdev_set_multicast_list 2694
[ 139.121815] ec_netdev_set_multicast_list 2694
[ 134.543074] ethernet link state:disconnected
[ 141.143419] exit
[ 141.143937] ecp->autoneg:1
autoneg -> speed:100, duplex:full, pause: non-supported
[ 141.144618] set_mac_according_aneg
[ 141.144623] opmode regs old value - 0x2202
[ 141.144967] old MII_BMCR: 0x3100
[ 141.145642] new MII_BMCR: 0x3100
[ 141.145646] hw_regs->er_opmode:0x2202
[ 141.145985] link established.
[ 141.148931] ethernet link state:linked
[ 141.153601] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 141.160039] ec_netdev_set_multicast_list 2694
[ 141.161135] read phy reg-4
[ 141.161486] read phy reg-0
[ 141.161827] read phy reg-5
[ 141.168551] ec_netdev_set_multicast_list 2694
[ 141.177889] ec_netdev_set_multicast_list 2694
[ 142.842733] ec_netdev_set_multicast_list 2694
[ 149.033904] ec_netdev_set_multicast_list 2694
[ 163.118749] ec_netdev_set_multicast_list 2694
[ 163.118906] ec_netdev_set_multicast_list 2694
[ 163.118940] ec_netdev_set_multicast_list 2694
[ 163.120103] ec_netdev_set_multicast_list 2694
[ 158.853070] ethernet link state:disconnected
[ 184.353409] exit
[ 184.353927] ecp->autoneg:1
autoneg -> speed:100, duplex:full, pause: non-supported
[ 184.354614] set_mac_according_aneg
[ 184.354619] opmode regs old value - 0x2202
[ 184.354961] old MII_BMCR: 0x3100
[ 184.355636] new MII_BMCR: 0x3100
[ 184.355641] hw_regs->er_opmode:0x2202
[ 184.355979] link established.
[ 184.358926] ethernet link state:linked
[ 184.363600] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 184.370055] ec_netdev_set_multicast_list 2694
[ 184.371157] read phy reg-4
[ 184.371505] read phy reg-0
[ 184.371847] read phy reg-5
[ 184.378595] ec_netdev_set_multicast_list 2694
[ 184.388022] ec_netdev_set_multicast_list 2694
[ 185.819024] nf_conntrack: automatic helper assignment is deprecated and it will be removed soon. Use the iptables CT target to attach helpers instead.
[ 186.092769] ec_netdev_set_multicast_list 2694
[ 192.557868] ec_netdev_set_multicast_list 2694
[ 307.882408] [PowerGate] name: 'usb2_1', on: 0, before SPS_PG_CTL: 0x74ff64
[ 307.889266] [PowerGate] name: 'usb2_1', on: 0, after SPS_PG_CTL: 0x74ff60
[ 307.897104] aotg_hcd aotg_hcd.1: fail to request vbus gpio [36]
[ 307.903067] vbus_otg_en_gpio:36
[ 307.906197] res_mem->start--end = 0xb0700000--0xb0700fff
[ 307.911489] irq = 93
[ 307.913716] aotg_hcd aotg_hcd.1: pdev->id probe:1
[ 307.918408] [PowerGate] name: 'usb2_1', on: 1, before SPS_PG_CTL: 0x70ff60
[ 307.925357] [PowerGate] name: 'usb2_1', on: 1, after SPS_PG_CTL: 0x74ff64
[ 307.932141] aotg_hcd aotg_hcd.1: usb reset OK: 0.
[ 307.937033] aotg_hcd aotg_hcd.1: AOTG USB Host Controller Driver
[ 307.943291] aotg_hcd aotg_hcd.1: new USB bus registered, assigned bus number 3
[ 307.950528] aotg_hcd aotg_hcd.1: irq 93, io mem 0xb0700000
[ 307.956037] aotg_hcd aotg_hcd.1: start
[ 307.960344] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
[ 307.967889] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 307.975120] usb usb3: Product: AOTG USB Host Controller Driver
[ 307.980932] usb usb3: Manufacturer: Linux 3.10.37 aotg_hub_hcd
[ 307.986764] usb usb3: SerialNumber: aotg_hcd.1
[ 307.991702] hub 3-0:1.0: USB hub found
[ 307.995530] hub 3-0:1.0: 1 port detected
[ 307.999694] USBEIEN(0xf06d650b): 0x80
[ 308.003496] aotg_hcd aotg_hcd.1: hcd controller initialized. OTGIRQ: 0x00, OTGSTATE: 0x02
[ 308.011752] USBEIRQ(0xf06d650a): 0x00
[ 308.113434] port_no:1 OTG IRQ, OTGSTATE: 0x03, USBIRQ:0x00
[ 308.122422] aotg_hcd aotg_hcd.1: aotg_hcd.1 connection changed: 1, acthcd->inserted: 1
[ 308.130836] aotg_hub_hotplug_timer:1955, dbg!
[ 308.412413] usb 3-1: new full-speed USB device number 2 using aotg_hcd
[ 308.418927] think_time:1
[ 308.421442] think_time:0x14
[ 308.424223] aotg_hcd aotg_hcd.1: device addr : 0x00000000
[ 308.602501] aotg_hcd aotg_hcd.1: ep0 index 0 from ep [in]
[ 308.622421] think_time:1
[ 308.624941] think_time:0x14
[ 308.627722] aotg_hcd aotg_hcd.1: device addr : 0x00000002
[ 308.634987] usb 3-1: New USB device found, idVendor=24ae, idProduct=1001
[ 308.641670] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 308.648808] usb 3-1: Product: Rapoo 2.4G Wireless Touch Desktop
[ 308.654816] usb 3-1: Manufacturer: MOSART Semi.
[ 308.662078] input: MOSART Semi. Rapoo 2.4G Wireless Touch Desktop as /devices/platform/aotg_hcd.1/usb3/3-1/3-1:1.0/input/input2
[ 308.673706] think_time:1
[ 308.676233] think_time:0x14
[ 308.679458] hid-generic 0003:24AE:1001.0001: input,hidraw0: USB HID v1.10 Keyboard [MOSART Semi. Rapoo 2.4G Wireless Touch Desktop ] on usb-aotg_hcd.1-1/input0
[ 308.696516] input: MOSART Semi. Rapoo 2.4G Wireless Touch Desktop as /devices/platform/aotg_hcd.1/usb3/3-1/3-1:1.1/input/input3
[ 308.708147] think_time:1
[ 308.710669] think_time:0x14
[ 308.714406] hid-generic 0003:24AE:1001.0002: input,hiddev0,hidraw1: USB HID v1.10 Mouse [MOSART Semi. Rapoo 2.4G Wireless Touch Desktop ] on usb-aotg_hcd.1-1/input1
[ 334.847164] [SNDRV]:[atm7059_link_hw_params] ###atm7059_link_hw_params
[ 334.852337] atm7059_dai_hw_params,SNDRV_PCM_FORMAT_S32_LE
[ 334.974583] [SNDRV]:[atc2603c_audio_hw_free] atc2603c_audio_hw_free
[ 334.975039] [SNDRV]:[atc2603c_audio_hw_free] atc2603c_audio_hw_free
[ 334.987266] [SNDRV]:[atm7059_link_hw_params] ###atm7059_link_hw_params
[ 334.991489] atm7059_dai_hw_params,SNDRV_PCM_FORMAT_S32_LE
[ 335.009376] [SNDRV]:[atc2603c_audio_hw_free] atc2603c_audio_hw_free
[ 335.009869] [SNDRV]:[atc2603c_audio_hw_free] atc2603c_audio_hw_free
[ 335.012547] [SNDRV]:[atm7059_link_hw_params] ###atm7059_link_hw_params
[ 335.016567] atm7059_dai_hw_params,SNDRV_PCM_FORMAT_S32_LE
[ 335.022482] [SNDRV]:[atc2603c_audio_hw_free] atc2603c_audio_hw_free
[ 335.023033] [SNDRV]:[atc2603c_audio_hw_free] atc2603c_audio_hw_free
[ 335.025369] [SNDRV]:[atm7059_link_hw_params] ###atm7059_link_hw_params
[ 335.027969] atm7059_dai_hw_params,SNDRV_PCM_FORMAT_S32_LE
[ 335.072934] [SNDRV]:[atm7059_link_hw_params] ###atm7059_link_hw_params
[ 335.077071] [SNDRV]:[atc2603c_audio_hw_free] atc2603c_audio_hw_free
[ 335.077488] [SNDRV]:[atc2603c_audio_hw_free] atc2603c_audio_hw_free
[ 335.079735] [SNDRV]:[atm7059_link_hw_params] ###atm7059_link_hw_params
[ 335.085058] [SNDRV]:[atc2603c_audio_hw_free] atc2603c_audio_hw_free
[ 335.085445] [SNDRV]:[atc2603c_audio_hw_free] atc2603c_audio_hw_free
[ 335.087417] [SNDRV]:[atm7059_link_hw_params] ###atm7059_link_hw_params
[ 335.091653] [SNDRV]:[atc2603c_audio_hw_free] atc2603c_audio_hw_free
[ 335.092104] [SNDRV]:[atc2603c_audio_hw_free] atc2603c_audio_hw_free
[ 335.094961] [SNDRV]:[atc2603c_audio_hw_free] atc2603c_audio_hw_free
[ 335.095474] [SNDRV]:[atc2603c_audio_hw_free] atc2603c_audio_hw_free
[ 335.098363] [SNDRV]:[atm7059_link_hw_params] ###atm7059_link_hw_params
[ 335.100795] atm7059_dai_hw_params,SNDRV_PCM_FORMAT_S32_LE
[ 335.120247] [SNDRV]:[atm7059_link_hw_params] ###atm7059_link_hw_params
[ 335.125624] [SNDRV]:[atc2603c_audio_hw_free] atc2603c_audio_hw_free
[ 335.126047] [SNDRV]:[atc2603c_audio_hw_free] atc2603c_audio_hw_free
[ 335.128637] [SNDRV]:[atm7059_link_hw_params] ###atm7059_link_hw_params
[ 335.134325] [SNDRV]:[atc2603c_audio_hw_free] atc2603c_audio_hw_free
[ 335.134788] [SNDRV]:[atc2603c_audio_hw_free] atc2603c_audio_hw_free
[ 335.136984] [SNDRV]:[atm7059_link_hw_params] ###atm7059_link_hw_params
[ 335.141499] [SNDRV]:[atc2603c_audio_hw_free] atc2603c_audio_hw_free
[ 335.141947] [SNDRV]:[atc2603c_audio_hw_free] atc2603c_audio_hw_free
[ 335.142580] [SNDRV]:[atc2603c_audio_hw_free] atc2603c_audio_hw_free
[ 335.143055] [SNDRV]:[atc2603c_audio_hw_free] atc2603c_audio_hw_free
[ 335.154663] [SNDRV]:[atm7059_link_hw_params] ###atm7059_link_hw_params
[ 335.156840] atm7059_dai_hw_params,SNDRV_PCM_FORMAT_S32_LE
[ 335.162804] snd_pcm_mmap,default
[ 335.208306] [SNDRV]:[atm7059_link_hw_params] ###atm7059_link_hw_params
[ 335.212262] snd_pcm_mmap,default
[ 340.380723] [SNDRV]:[atc2603c_audio_hw_free] atc2603c_audio_hw_free
[ 340.381051] [SNDRV]:[atc2603c_audio_hw_free] atc2603c_audio_hw_free
[ 340.383332] [SNDRV]:[atc2603c_audio_hw_free] atc2603c_audio_hw_free
[ 340.383673] [SNDRV]:[atc2603c_audio_hw_free] atc2603c_audio_hw_free
